Abstract:Two-dimensional tungsten disulfide (WS2) nanosheets hold great potential for improving the mechanical properties of polymer nanocomposites, yet their large-scale preparation, dispersion, and toughening efficiency remain challenging. Herein, a facile, scaled-up, and eco-benign method was developed to simultaneously exfoliate and fabricate surface-functionalized WS2 nanosheets with the assistance of biobased polyphenols, such as tannic acid (TA) from peel waste. Benefiting from the strong interfacial interaction between TA-modified WS2 nanosheets (WS2-TA) and the epoxy resin (EP) matrix, considerable improvement in the mechanical properties of the EP/WS2-TA nanocomposites was achieved. The introduction of barely 0.25 wt % WS2-TA nanosheets increased the tensile and flexural strengths by 63 and 35%, respectively. Meanwhile, with the same low loading of 0.25 wt %, the impact strength and fracture toughness (KIc) of the nanocomposites, respectively, increased by 131 and 96%, realizing highly efficient toughening of EP. Besides, the thermal properties of the EP/WS2-TA nanocomposites also achieved noticeable improvements, which were attributed to the good dispersion of the nanosheets, combining inherently rigid and flexible nature, and the strong interfacial interaction between the nanosheets and the EP matrix. This work not only highlighted the simultaneous exfoliation and surface functionalization of the two-dimensional (2D) nanosheets but also broadened their applications in high-performance nanocomposites.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsanm.1c01938.Illustration of the exfoliation procedure by ball milling; high-resolution XPS spectra of W 4f from the WS2-TA nanosheets; confocal images of bulk WS2 and the nanosheets excited at 500–700 nm; nonisothermal DSC curves of EP, EP/0.25 wt % WS2, and EP/0.25 wt % WS2-TA with different heating rates; TG and DTG curves of the EP/WS2 nanocomposites; and SEM image of the fractured interface morphology of EP/0.35 wt % WS2-TA (PDF)This article has not yet been cited by other publications.

Facile synthesis of WS2@GO nanohybrids for significant improvement in mechanical and tribological performance of EP composites

Simultaneously enhancing tribological and mechanical properties of epoxy composites using basalt fiber/reduced graphene oxide/paraffin wax

Preparation and tribological properties of graphene oxide/nano-MoS2 hybrid as multidimensional assembly used in the polyimide nanocomposites

Tribological Behavior of UHMWPE Reinforced with Graphene Oxide Nanosheets

Space‐confined thermal disintegration synthesis of graphene‐copper nanohybrids for enhanced tribological behaviors of epoxy‐based composites

3D Structurally Advanced Graphene Oxide/h-Bn Hybrid for Solid Self-Lubrication with Enhanced Thermal Conductivity

Tribological properties of polyimide coatings filled with graphene oxide and MXene composite nanofillers

Hybridization of Polytetrafluorethylene Fibers and Multiscale Short Carbon Fibers to Significantly Improve the Tribological Performance of Polyphenylene Sulfide

Synergistic effects of bioprotein decoration and WS2 @Ti3C2 nanohybrids on the interfacial and tribological performance of PPS/PTFE fabric composites

Synergistically assembled RGO/Si3N4 whiskers hybrid aerogels to endow epoxy composites with excellent thermal and tribological performance

Preparation and Tribological Behaviors of Lubrication-Enhanced PEEK Composites

Synergism Lubrication of Graphene and Carbon Nanotube in Polymeric Composites under Drying Sliding Condition

Attaching ZrO2 nanoparticles onto the surface of graphene oxide via electrostatic self-assembly for enhanced mechanical and tribological performance of phenolic resin composites

Preparation and tribological behaviors of poly (ether ether ketone) nanocomposite films containing graphene oxide nanosheets

Enhancement of Friction Performance Enabled by a Synergetic Effect Between Graphene Oxide and Molybdenum Disulfide

Low Loading of Tannic Acid-Functionalized WS 2 Nanosheets for Robust Epoxy Nanocomposites

Improving tribological performance of porous oil-impregnated GO/PA6 composites with double lubrication structure

High-performance epoxy nanocomposites via constructing a rigid-flexible interface with graphene oxide functionalized by polyetheramine and f-SiO 2

In situ exfoliation and surface functionalization of graphene oxide for epoxy composites with improved thermal and mechanical properties

Simultaneous Improvements in Wear Resistance and Mechanical Properties of Uhmwpe Nanocomposite Fabricated Via A Facile Approach

Synergy of core-shell Cu@rGO hybrids for significantly improved thermal and tribological properties of polyimide composites