Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

The mechanisms of elevated temperature property losses in high performance structural epoxy resin matrix materials after exposures to high humidity environments

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Chemical, mechanical and morphological investigation on the hygrothermal aging mechanism of a toughened epoxy

Roles of hygrothermal aging temperature and time in degradation of the fracture toughness of highly cross‐linked epoxy

Effects of High-Temperature Storage on the Elasticity Modulus of an Epoxy Molding Compound

Dynamic Mechanical Properties and Thermal Effect of an Epoxy Resin Composite, Encapsulation’s Element of a New Electronic Component

Study of Heat Treatment Effect on Mechanical Properties of Epoxy Resin Reinforced with Fiber Glass

On the Thermal-Behavior and Mechanism of Residual Microstress Buildup at the Matrix Interface in Filled Epoxy-Resins

Molecular Dynamics Investigation of the Thermo-Mechanical Properties of the Moisture Invaded and Cross-Linked Epoxy System

The hygrothermal aging process and mechanism of the novolac epoxy resin

The effect of clay on the mechanical properties of epoxy resins subjected to hygrothermal ageing

Aging by moisture and/or temperature of epoxy/SiC composites: Thermal and mechanical properties

Moisture and Glass Transition Temperature Kinetics of Ambient-Cured Carbon/Epoxy Composites

Influence of Long-Term Moisture Exposure and Temperature on the Mechanical Properties of Hybrid FRP Composite Specimens

Effects of Moisture Ingress on the Mesoscale Mechanical Properties of Epoxy Adhesives under Elevated Temperature

Moisture absorption process of epoxy resin and mechanical properties of its fiber composites

Transverse impacts‐induced deformation and damage of 3D angle‐interlock woven composites at elevated temperatures

The effects of a water environment on anomalous absorption behavior in graphite/epoxy composites

Longitudinal tensile analysis of carbon fiber/epoxy composites under the coupling effect of high and low temperature cycle-humidity-bending load

Elevated temperature effect on tension fatigue behavior and failure mechanism of carbon/epoxy 3D angle-interlock woven composites

Mechanical Behavior of GFRP Laminates Exposed to Thermal and Moist Environmental Conditions: Experimental and Model Assessment