Abstract:Residual stresses can have detrimental effect on the life cycle of engineering components and can affect the accuracy of the fatigue life prediction models. Accurate measurement of these stresses are therefore crucial. . However, destructive and semi-destructive methods of measuring residual stresses often cause damage to the components. In contrast, the non-destructive ultrasonic method allows for intact measurement of residual stresses even, in situation where portability is not feasible. Various waves can be utilized in the ultrasonic method for measuring residual stresses. In this study, longitudinal critically refracted (LCR) waves were employed due to their higher sensitivity, larger scanning area, and lower sensitivity to texture effect, making them preferable over other waves. The purpose of this study was to investigate the influence of plasticity on the measurement of residual stresses using the ultrasonic method. To achieve this, two stainless steel disks were subjected to quenching at temperatures of 300 °C and 700 °C to induce different levels of residual stresses and plasticity. The material properties of the disks were determined through standard tensile tests to facilitate numerical simulations. Tensile test specimens were extracted from the initial sheet to measure the yield stress and modulus of elasticity. The coefficient of acoustoelasticity, was determined by subjecting the tensile test specimens to different stress levels and recording the wave flight time. The coefficient of acoustoelasticity for stainless steel 316Lwas obtained using the slope of and (E(t-t0))/t0,. Residual stresses were experimentally measured using both the ultrasonic method and the center-hole drilling method, and the results were compared with those obtained from numerical analyses. The findings from center-hole drilling method, ultrasonic method, and numerical simulation were then compared and discussed. Different levels of plasticity were considered, and the accuracy of measuring residual stresses was analyzed and evaluated.

Effect of Anisotropy on Residual Stress Measurement of 316L Stainless Steel by Ultrasonic Surface Wave

Plane Residual Stress Measurement Using Ultrasonic Considering Weak Anisotropy of Metallic Material

A study on the effect of plasticity on the measurement of residual stresses using ultrasound technique

Investigation on the Evolution of Residual Stress in Ultrasonic Surface Rolling Treatment-Processed 18CrNiMo7-6 Alloy Steel

Simulation of Residual Stress of V-Notch Specimen Treated by Ultrasonic Rolling

Ultrasonic Measurement of Stress in SLM 316L Stainless Steel Forming Parts Manufactured Using Different Scanning Strategies

Relieving Residual Stress of 316L Stainless Steel by Acoustic/Thermal Composite Treatment

Plane Stress Measurement of Orthotropic Materials Using Critically Refracted Longitudinal Waves

Reconstruction Mechanism of Surface Integrity for Laser Additive Manufactured 316 L Stainless Steel Subjected to Ultrasonic Surface Rolling Process: Numerical Simulation and Experimental Verification

Effects of factors from practical workpieces on ultrasonic LCR method stress measurement

Effect of ultrasonic surface impact on the microstructural characterization and mechanical properties of 316L austenitic stainless steel

Surface Properties of Additively Manufactured 316L Steel Subjected to Ultrasonic Rolling

Comparison of residual stress determination using different crystal planes by short-wavelength X-ray diffraction in a friction-stir-welded aluminum alloy plate

Anisotropy of Mechanical Properties and Residual Stress in Additively Manufactured 316L Specimens

Effects of ultrasonic surface rolling process on tribological behavior of 4Cr13 stainless steel

Enhanced Fatigue Performance and Surface Mechanical Properties of AISI 304 Stainless Steel Induced by Electropulsing-Assisted Ultrasonic Surface Rolling Process

Anisotropic Plasticity Behavior of Rolled 316L Ultra-Thin Sheet and Its Application to Micro-Deep Drawing Modeling

An Investigation of Fretting Fatigue Behavior and Mechanism in 17-4PH Stainless Steel with Gradient Structure Produced by an Ultrasonic Surface Rolling Process

Influence of surface roughness on laser ultrasonic detection for laser powder bed fusion manufactured 316L stainless steel

The Role of Residual Stress in Anisotropic Mechanical Properties of Titanium Alloy after Rolling

Effects of Ultrasonic Surface Rolling Parameters on Surface Integrity of TC17 Alloy