Abstract:Copper as well as copper base composites reinforced with coated and uncoated 1 wt% diamond, graphite particles or short carbon fibers are prepared by powder metallurgy process. The reinforcement particles were encapsulated with silver as well as copper layer by using the electroless deposition technique to investigate the influence of the reinforcement surface coating on the microstructure, density, electrical and thermal properties of the sintered samples. The coated and the uncoated powders were cold compacted at 600 MPa, and then sintered at 1173 K (900°C) for 2 h under hydrogen atmosphere. The phase composition, morphology and microstructure of the prepared powders as well as the copper base sintered composites were investigated using X-ray diffraction analysis (XRD) and Scanning Electron Microscope (SEM) equipped with an Energy Dispersive Spectrometer (EDS) respectively. The density of the sintered composites was measured by Archimedes method. The copper base consolidated composites had a density up to 96% and the reinforcement coated particles were distributed uniformly within the copper matrix better than the uncoated one. The electrical resistivity at room temperature and the heat transfer conduction of the produced samples were measured in a temperature range between 323 K (50°C) and 393 K (120°C). The results observed that the sintered materials prepared from the coated powder have lower electrical resistivity than the sintered materials prepared from the mixed powders. On the other hand the thermal conductivity values were calculated using the heat transfer conduction values by means of the Fourier formula. The results observed that the thermal conductivity of copper is (391 W/m·K), 1 wt% diamond/Cu is (408 W/m·K), 1 wt% graphite coated silver/Cu is (393 W/m·K), 1 wt% Cu coated short carbon fiber/Cu is (393 W/m·K), graphite/Cu is (383 W/m·K) and short carbon fiber/Cu is (382 W/m·K). The obtained composites are expected to be suitable for heat sink applications. The heat transfer testing experiments were done. The forced convection of the present work was done and compared with the previous work in the literature, and satisfactory agreement was achieved.

Novel advanced copper-silver materials produced from recycled dendritic copper powders using electroless coating and hot pressing

Enhancement of electrical and thermal conductivity of low-cost novel Cu–Ag alloys prepared by hot-pressing and electroless plating from recycled electrolytic copper powders

The effect of silver coated copper particle content on the properties of novel Cu-Ag alloys prepared by hot pressing method

Fabrication and performance of silver coated copper powder

Preparation and anti-oxidisation resistance of silver-coated copper powders by cobalt-modified copper powders

Synthesis and Characterization of Silver-Coated Copper Powder Layer

Surface modification for improving interfacial, mechanical and thermal performance characteristics in epoxy composites: Electroless nickel enhancement of dendritic copper particle-reinforced epoxy

Preparation and sintering properties in air of silver-coated copper powders and pastes

The Effect of Selective Laser Melting Process on the Microstructure, Density, and Electrical Conductivity of Silver-Coated Copper Cores

Preparation of silver-coated copper powder and its oxidation resistance research

Study of Preparation on the Flake Silver Coating over Copper Powder for Electronic Industry

Electrical properties of electrically conductive adhesives from epoxy and silver-coated copper powders after sintering and thermal aging

Preparation of Flake Silver Coated over Copper Powder

Fabrication, Microstructure, Thermal and Electrical Properties of Copper Heat Sink Composites

Characterization of silver-coated copper particles synthesized by mechanical activation and electroless plating

Microstructure and wear characterization of Al2O3 reinforced silver coated copper matrix composites by electroless plating and hot pressing methods

The effect of flake-like morphology on the coating properties of silver coated copper particles fabricated by electroless plating

A Study of Silver Decoration on Carbon Nanotubes via Ultrasonic Chemical Synthesis and Their Reinforced Copper Matrix Composites

Processing copper and silver matrix composites by electroless plating and hot pressing

Improvement of the thermal stability of dendritic silver-coated copper microparticles by surface modification based on molecular self-assembly