Abstract:This study aims to examine the 50/50 polypropylene/polyamide 6 (iPP/PA6) system molded under confined flow conditions, both in its original state and after being modified by two different interfacial agents. This study provides two main insights. Firstly, it focuses on a polymer blend close to phase inversion. Secondly, it investigates the impact of using two different types of interfacial agents (derived from polymer waste) to enhance the compatibility between iPP and PA6. Dynamic Mechanical Analysis (DMA) has been employed to achieve these objectives. It is important to note that the investigation of the 50/50 iPP/PA6 system is a crucial focus predicted in previous studies, where a series of mechanical properties were evaluated using Box–Wilson design of experiments (DOEs) over the whole compositional range on the iPP/PA6 binary system. Thus, two interfacial modifiers, namely succinic anhydride (SA)-grafted atactic polypropylene with terminal, side, and bridge SA grafts (aPP-SASA) and succinyl-fluoresceine (SF) with bridge succinic anhydride grafting atactic polypropylene (aPP-SFSA), were employed. The authors obtained and characterized these agents. The quantity of these agents used in the blend was identified as a critical coordinate in prior studies conducted by the authors. The processing method used, compression molding under confined conditions, was chosen to minimize any orientation effect on the emerging morphology. All characterization procedures were performed on samples processed by contour machining to retain the blend morphologies as they emerged from the processing stage. Results from WAXS and SAXS synchrotron tests concluded there were no changes in the crystal morphology of the iPP or the PA6 in the blends nor any co-crystallization process throughout the compositional range. These findings, and the long period fits on the PP crystalline phase for the fifty/fifty blends we are discussing, will support the present DMA study. Finally, the efficiency of these interfacial modifiers has been concluded, even in this unfavorable scenario.

Impact of Compatibilizer on the Electrical and Thermal Characteristics of Areca Fibre-Filled Polypropylene Composites

Effects of reactive compatibilization on the morphological, thermal, mechanical, and rheological properties of intumescent flame-retardant polypropylene.

Electrical Properties of Bamboo Fiber Reinforced Polypropylene Composite: Effect of Coupling Agent

Oil palm fiber reinforced polypropylene composites: effects of fiber loading and coupling agents on mechanical, thermal, and interfacial properties

Novel High‐dielectric‐permittivity Poly(vinylidene Fluoride)/polypropylene Blend Composites: the Influence of the Poly(vinylidene Fluoride) Concentration and Compatibilizer

Effects of compound compatibilizer and CaTiO3 filler on the properties of polypropylene/polyphenylene ether/glass fiber composites

Thermal Adsorption and Mechanical Behaviour of Polypropylene Hybrid Composite Synthesized by Glass/Hemp Fibre via an Injection Moulding Process

Effect of addition of compatibilizer on mechanical, thermal and thermo-mechanical behavior of a polymer blend (PBT/ PBT(G)/ PTT) composite

Short Nylon 6 Fibre Reinforced Polystyrene/Natural Rubber Blends: Effect of Maleated-Polystyrene Compatibiliser

Influence of Grafting Maleimide on the Insulating Properties in Polypropylene

Improvement of mechanical and wear resistance property by varying glass fiber contents and amino-silicate coupling agents on polyamide 612 composites

Study on Dielectric Property of the PP/PVDF Blending Composites

Does a Compatibilizer Enhance the Properties of Carbon Fiber-Reinforced Composites?

Effects of different coupling agents on the mechanical and interfacial properties of oil palm fiber reinforced polypropylene composites

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Polypropylene matrix embedded with Curaua fiber through hot compression processing: characteristics study

Effect of SEBS-MA and MAPP as coupling agent on the thermal and mechanical properties in highly filled composites of oil palm fiber/PP

Mechanical and Dielectric Properties of Graphene Incorporated Polypropylene Nanocomposites Using Polypropylene-Graft-maleic Anhydride As a Compatibilizer

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend

Mechanical behavior of carbon/glass polypropylene hybrid composites

Enhancing the performance of hybrid bio-composites reinforced with natural fibers by using coupling agents