Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Tuning the D‐Band Center of Bi2S3─MoS2 Heterostructure Towards Superior Lithium‐Sulfur Batteries

Bimetallic sulfides heterostructure efficient adsorption and catalytic of polysulfides for high-performance lithium-sulfur batteries

Tuning p‐Band Centers and Interfacial Built‐In Electric Field of Heterostructure Catalysts to Expedite Bidirectional Sulfur Redox for High‐Performance Li–S Batteries

Synergistic Polysulfides Adsorption–Conversion with Mo2C–MoO2 Heterostructure for Kinetically Enhanced Lithium–Sulfur Battery

Constructing MoS 2 -SnS heterostructures on N-doped carbon nanosheets for enhanced catalytic conversion of polysulfides in lithium-sulfur batteries

Tuning the Band Structure of MoS 2 via Co 9 S 8 @MoS 2 Core–Shell Structure to Boost Catalytic Activity for Lithium–Sulfur Batteries

Synergistic coupling between Fe7S8-MoS2 heterostructure and few layers MoS2-embeded N-/P-doping carbon nanocapsule enables superior Li-S battery performances

Synergistic Adsorption-Electrocatalysis of 2D/2D Heterostructure Toward High Performance Li-S Batteries

Insight into MoS 2 –MoN Heterostructure to Accelerate Polysulfide Conversion toward High‐Energy‐Density Lithium–Sulfur Batteries

Facile Synthesis of Heterostructured MoS 2 –MoO 3 Nanosheets with Active Electrocatalytic Sites for High-Performance Lithium–Sulfur Batteries

Rational design of hollow flower-like MoS2/Mo2C heterostructures in N-doped carbon substrate for synergistically accelerating adsorption-electrocatalysis of polysulfides in lithium sulfur batteries

Manipulating Redox Kinetics using p‐n Heterojunction Biservice Matrix as both Cathode Sulfur Immobilizer and Anode Lithium Stabilizer for Practical Lithium–Sulfur Batteries

NiS2-MoS2@MXene heterostructures for enhancing polysulfide adsorption and conversion of Li S battery

Enhanced Polysulfide Regulation <i>via</i> Porous Catalytic V<sub>2</sub>O<sub>3</sub>/V<sub>8</sub>C<sub>7</sub> Heterostructures Derived from Metal-Organic Frameworks toward High-Performance Li-S Batteries

Modulating d‐Band Electronic Structures of Molybdenum Disulfide via p/n Doping to Boost Polysulfide Conversion in Lithium‐Sulfur Batteries

A hollow Co0.12Ni1.88S2/NiO heterostructure that synergistically facilitates lithium polysulfide adsorption and conversion for lithium-sulfur batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Dual-heterostructures decorated interweaved carbon nanofibers sulfur host for high performance lithium-sulfur batteries

Enhanced Adsorption and Conversion of Polysulfides by ZIF‐67‐Based Co3O4/TiO2 Heterostructure and Attached Polypyrrole 3D Conductive Network for Lithium–Sulfur Batteries with Stable and Extended Cycling

Bottom-up synthesis of 2D heterostructures enables effective polysulfides inhibition and conversion

Optimized Catalytic WS2–WO3 Heterostructure Design for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries