Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Constructing MoS 2 -SnS heterostructures on N-doped carbon nanosheets for enhanced catalytic conversion of polysulfides in lithium-sulfur batteries

Rational design of hollow flower-like MoS2/Mo2C heterostructures in N-doped carbon substrate for synergistically accelerating adsorption-electrocatalysis of polysulfides in lithium sulfur batteries

Facile Synthesis of Heterostructured MoS 2 –MoO 3 Nanosheets with Active Electrocatalytic Sites for High-Performance Lithium–Sulfur Batteries

MoS2 Quantum Dots-Decorated CNTs Networks as Sulfur Host Enhanced Electrochemical Kinetics for Advanced Lithium–Sulfur Batteries

N-Doped Carbon Fiber-Encapsulated CoS 2 /SnS 2 Heterostructures Facilitate Polysulfide Conversion for Lithium–Sulfur Batteries

Bimetallic sulfides heterostructure efficient adsorption and catalytic of polysulfides for high-performance lithium-sulfur batteries

NiS2-MoS2@MXene heterostructures for enhancing polysulfide adsorption and conversion of Li S battery

Synergistic catalysis of MoS2-Ni3S2 heterojunctions to accelerate polysulfide conversion for high-performance Li-S battery

In-situ constructed three-dimensional MoS2–MoN heterostructure as the cathode of lithium–sulfur battery

Insight into MoS 2 –MoN Heterostructure to Accelerate Polysulfide Conversion toward High‐Energy‐Density Lithium–Sulfur Batteries

Synergistic Polysulfides Adsorption–Conversion with Mo2C–MoO2 Heterostructure for Kinetically Enhanced Lithium–Sulfur Battery

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Sulfur-deficient MoS2-carbon hollow nanospheres for synergistic trapping and electrocatalytic conversion of polysulfides

Core-shell polyoxometalate-based zeolite imidazole framework-derived multi-interfacial MoSe2/CoSe2@NC enabling multi-functional polysulfide anchoring and conversion in lithium-sulfur batteries

Rich Heterointerfaces Enabling Rapid Polysulfides Conversion and Regulated Li2S Deposition for High-Performance Lithium-Sulfur Batteries.

Catalytic-conversion behavior of MoS2 for polysulfides by nickel introduction and phosphorous-doping in advanced lithium-sulfur batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Mo‐O‐C Between MoS2 and Graphene Toward Accelerated Polysulfide Catalytic Conversion for Advanced Lithium‐Sulfur Batteries

SnS/SnS2 Heterostructures Embedded in Hierarchical Porous Carbon As Polysulfides Immobilizer for High-Performance Lithium-Sulfur Batteries

Covalent Coupled Sulfur-Deficient MoS2 Nanosheets on Carbon Nanotubes toward Polysulfide Catalytic Conversion in a Lithium Sulfur Battery

Construction of SnS2-modified multi-hole carbon nanofibers with sulfur encapsulated as free-standing cathode electrode for lithium sulfur battery