Abstract:Epoxy/Al as a functional structural energetic composite material that can be used as an adhesive, energetic fragments and warhead shells due to its high energy density, low density, and high strength. It can release a large amount of chemical energy (about 21.36 kJ/g) through chemical reactions when subjected to high-speed impact and thermal stimulation. Whether used as a matrix or auxiliary component, it has enormous development potential. Therefore, it is particularly important to study the mechanical properties of Epoxy/Al energetic composite materials under different temperature environments and strain rates of loading. This article describes the preparation of Epoxy/Al specimens with a mass percentage of 70%–30% using vacuum curing after 24 h under 0.8 Bar and 50 °C. The mechanical properties of Epoxy/Al specimens under different loading conditions were characterized using a high and low temperature universal testing machine and a separate Hopkinson experimental system. The modulus prediction method of binary composite materials was improved by combining SEM (scanning electron microscopy) and microstructure, and an adaptive constitutive model was developed combined with the K Srinivas model and neural network model based on the Sherwood Frost empirical constitutive relationship. The results show that Epoxy/Al energetic composite material has a significant temperature effect. When the temperature exceeds 100 °C, Epoxy/Al energetic composite material will be a significant physical and chemical property transition (the specimen exhibits viscous fluid characteristics and gradually begins to slowly decompose). As the temperature decreases, the specimen gradually exhibits a certain degree of brittleness and strength is improved. Due to the deformation, displacement, and interfacial debonding of internal particles during the loading process, Epoxy/Al materials exhibit excellent impact energy absorption effects, with energy absorption reaching 15.30 MJ/m 3 at room temperature, and unit mass cost much lower than popular CFRP (carbon fiber-reinforced polymer) materials (CFRP energy absorption cost is 0.268 J/g/£, while Epoxy/Al materials do not exceed 0.013 J/g/£). During the dynamic loading process, Epoxy/Al energetic composite materials exhibit a phenomenon of structural reconstruction and enhancement throughout the entire loading process. The maximum strength at room temperature can reach 240.70 MPa, which is superior to all existing energetic materials of the same type. By introducing interface effects and quantifying them in the Halpin Tsai model, the existing prediction method for the Young's modulus of binary particle added composite materials has been effectively improved, reducing the prediction error of the Young's modulus of Epoxy/Al energetic composite materials from 14.2% to 2.4%. The numerical simulation results indicate that the newly developed constitutive model has high accuracy and can better reflect the mechanical properties of Epoxy/Al materials. The development method of this constitutive model has a positive contribution to the development of composite materials.

A multi-scale analysis to predict elastic response in different weight fractions of carbon fiber powder

Study of Elastic Modulus and Yield Strength of Polymer Thin Films Using Atomic Force Microscopy

Prediction of Fatigue Life of Polyetherimide/Carbon Fiber Particulate Composites at Various Maximum Stresses and Filler Contents

A combined molecular dynamics-finite element multiscale modeling to analyze the mechanical properties of randomly dispersed, chemisorbed carbon nanotubes/polymer nanocomposites

Fiber Orientation and Strain Rate-Dependent Tensile and Compressive Behavior of Injection Molded Polyamide-6 Reinforced with 20% Short Carbon Fiber

Effects of Carbon Fiber Content on the Crystallization and Rheological Properties of Carbon Fiber-Reinforced Polyamide 6

Parametric analysis of additively manufactured polymer nanocomposites: A experimental and multiscale study

Exploring the Effect of Specimen Size on Elastic Properties of Fused-Filament-Fabrication-Printed Polycarbonate and Thermoplastic Polyurethane

A Methodology to Predict the Fatigue Life under Multi-Axial Loading of Carbon Fiber-Reinforced Polymer Composites Considering Anisotropic Mechanical Behavior

Computational Analysis of Mechanical Properties in Polymeric Sandwich Composite Materials

Modeling Composites of Multi-Walled Carbon Nanotubes in Polycarbonate

Optimization of Flexural Performance of PETG Samples Produced by Fused Filament Fabrication with Response Surface Method

Comparison of Mechanical Property Simulations with Results of Limited Flexural Tests of Different Multi-Layer Carbon Fiber-Reinforced Polymer Composites

Effects of fiber and matrix properties on the compression strength of carbon fiber reinforced polymer composites

Optimization of geometrical factors for enhanced performance of carbon fiber reinforced polymer cores under transverse loading

Effects of infill density on mechanical properties of additively manufactured chopped carbon fiber reinforced PLA composites

Process-structure-property analysis of short carbon fiber reinforced polymer composite via fused filament fabrication

A comprehensive study of carbon nanoparticle shape and orientation effects on composite elastic properties using FEA

Enhanced Estimation of Axial Compressive Strength for CFRP Based on Microscale Numerical Simulation and the Response Surface Method

Influence of Fiber Volume in Hybrid Short Glass/Cellulose Reinforced Thermoplastic Compounds

Mechanical behavior and optimization of constitutive prediction model for Epoxy/Al energetic composite materials considering temperature and strain rate effects