Abstract:The effects of the area reductions on the crystal orientation, eccentricity, and mechanical properties of GH4145 alloy tubes prepared by three-roller cold rolling were studied. Electron backscattered diffraction analysis showed that the equiaxed grains of the annealed tube blank gradually changed into elongated crystals along the axial direction (AD) with increased deformation. In addition, the grain orientations rotated from random distribution towards the <101>//radial direction (RD), <111>//AD, and <101> + <111>//tangential direction (TD). Brass, copper, S, and {123}< 111‾ > textures formed and increased in strength with increasing strain. Room-temperature tensile tests loaded along the AD and TD demonstrated yielding anisotropy of the tubes. With increasing strain, the work hardening increased continuously, and the dislocations slipped in three directions and then transformed into slip bands and dislocation cells, whereas a few deformation twins formed as the reduction reached 64%, and then slipped in two directions. When the reduction was 64%, the activated slip system transformed from {111}<110> to {110}<001> in most grains under applied AD loading, which was consistent with the loading in both directions at a reduction of 72%. As the grains in the preferential deformation zone near the inner and outer walls rotated to the <101>//RD orientation, the tubes plastically deformed, and the grains in the central layer then gradually begin to rotate. The ratio of radial length in the deformation hysteresis zone to wall thickness was used to represent the degree of non-uniformity of the deformation. A direct correlation was found between the eccentricity of the wall thickness and the non-uniformity of tube deformation as the area reduction increased from 13% to 50%. In addition, the radial delamination of the tubes disappeared, deformation became uniform, and the eccentricity decreased significantly as the area reduction increase up to 64%. Therefore, the dimensional accuracy and uniformity of the tubes can be further improved by controlling the strain of the tube.

Evolution of Goss texture in thin-walled copper tube at different heat treatment temperatures

Formation and development of Goss texture in Al–Cu–Mg alloy during solution treatment

Texture evolution and its influence mechanism on properties of single crystal copper and polycrystalline copper during cumulative deformation

Evolution of Texture and Tensile Properties of Cold-Rotary Swaged Ti–6Al–4V Alloy Seamless Tubing after Annealing at Different Temperatures

In-situ EBSD Observation of Texture Evolution and Lattice Rotation Behavior in Shear Deformation of Thin-Walled Aluminum Alloy Tubes

The Influence of Thermal Cycle on the Grain Structure of Friction-Stir-Welded Pure Copper Joint

Effect of Cold Rolling Degree on Texture Evolution, Eccentricity, and Yielding Anisotropy of GH4145 Alloy Tubes

Evolution of microstructure and texture of moderately warm-rolled pure tungsten during annealing at 1300 °C

Deformation history and the resultant microstructure and texture in backward tube spinning of Ti–6Al–2Zr–1Mo–1V

Microstructure and Texture Evolution in Cold-Rolled and Annealed Oxygen-Free Copper Sheets

Microstructure Development and Texture Evolution of Aluminum Multi-Port Extrusion Tube During the Porthole Die Extrusion

Effect of annealing temperature on the texture evolution and ovality of GH4145 alloy tubes with various numbers of rolling passes

Microstructures and mechanical properties of Cu-Sn alloy subjected to elevated-temperature heat deformation

New insight of texture and microstructure evolution, and the connections between with tensile performance in as-annealed Al-Cu-Mg-Zr sheet

Microstructure and Texture of Pure Copper under Large Compression Deformation and Different Annealing Times

Effect of Annealing Temperature on microstructure and properties of the Microtubes for GH4169 alloy

Effects of evolution of nanoscale copper precipitation and copper content on mechanical properties of high-strength steel weld metal

Effect of Thermal Treatment on the Mechanical Properties of Cu Specimen Fabricated Using Electrodeposition Bath for Through-Silicon-via Filling

Discontinuous yielding behavior, strengthening effect and deformation mechanism of double wall copper-brazed steel tube under various continuous sectional cooling

Texture evolution and twinnability prediction of the most compliant orientation in GH3536 superalloy during cold rolling

Effects of Extrusion Temperature on Texture Evolution in Mg-1Gd Alloy