Abstract:Few researches on high efficiency modified phosphogypsum (MPG) and its resource utilization in bulding materials. This article investigated the effects of different lower temperatures and drying times on the thermodynamic modification mechanism of macroscopic performance and microscopic structure of MPG, and investigates its application in phosphogypsum-based self-leveling mortars (PBSLM). Then, the coupling mechanism of characteristic heavy metals in the modification process (original-modification-hydration) was discussed, and the safety evaluation was conducted on the content of heavy metal elements in the sample. Data from microscopic analysis showed that with the increase of temperature and drying time, the strength of MPG blocks and the decomposition rate of dihydrate gypsum crystal both increased, while the particle size decreased. The degree of crystal decomposition becomes more complete as the temperature rises if the holding time remains constant. As well as, the MPG at 180 °C/7 h, 195 °C/7 h/10 h met the Chinese standard of " Calcined gypsum " (GB/T9776). The heavy metal elements in MPG decreased obviously, caused by the substitution solid solution formed by Ca 2+ and Fe 3+ and heavy metal ions and the adsorption of calcium sulfate hemihydrate crystals. After hydration of MPG, As and Cd increased slightly because dicalcium phosphate was insoluble in water and soluble in acid, and iron oxide reduced and dissolved Cd. Then, the ecological hazards of heavy metals in hydrated MPG after hydration were evaluated. The results showed that there was no environmental safety problem in the hydrated MPG, but the As and Cr elements in it had an acceptable carcinogenic risk through oral intake. Based on ensuring the safety of MPG, MPG powder was used in PBSLM. The research demonstrates that the basic mechanical properties of the PBSLM produced, when the MPG powder content is 330 g, and cement is 40 g are the best. The heavy metal aqueous solution's leaching amount is lower than China's national standard limit value. (30min fluidity, 24 h-flexural and compressive strength were 154 mm, 5.7 MPa and 10.6 MPa). Finally, based on this research, a set of general evaluation system for safe utilization of solid waste was established according to national standards. This provides theoretical support for the research of heavy metal in PG at low temperature and the ways of harmless and resource utilization.

Green-brick preparation method for the resource utilization of sewage sludge and phosphogypsum with a low heavy-metal pollution risk

Recycling of Heavy Metal Contaminated River Sludge into Unfired Green Bricks: Strength, Water Resistance, and Heavy Metals Leaching Behavior – A Laboratory Simulation Study

Recycling of Waste River Sludge into Unfired Green Bricks Stabilized by a Combination of Phosphogypsum, Slag, and Cement

The Long-Term Leaching Behavior of Heavy Metals in Geopolymers and Portland Cement Bricks Containing Mswi Fly Ash: A Comparative Study

Preparation,properties and environmental safety of fired bricks made from lake silt and sewage sludge

The reuse of waste glass to enhance strength during the introduction of municipal sewage sludge in shale brick manufacturing

Properties of Cemented Filling Materials Prepared from Phosphogypsum-Steel Slag-Blast-Furnace Slag and Its Environmental Effect

Modification mechanism, heavy metal coupling and ecological security risk assessment of phosphogypsum utilization in self-leveling mortar

Preparation of phosphogypsum-copper smelting slag-based consolidating body with high compressive strength

Experimental Study on Performance, Hydration, and Sustainability of Coal Gasification Coarse Slag Based Geopolymers for Sustainable Environment

Characteristic pollutant purification analysis of modified phosphogypsum comprehensive utilization

Effect of varying water content and extreme weather conditions on the mechanical performance of sludge bricks solidified/stabilized by hemihydrate phosphogypsum, slag, and cement

Preparation and Properties of Green High Ductility Geopolymer Composites Incorporating Recycled Fine Brick Aggregate

Preparation of Load-Bearing Building Materials from Autoclaved Phosphogypsum

Utilization of waste phosphogypsum to prepare non-fired bricks by a novel Hydration–Recrystallization process

Solidification and stabilization of Pb-Zn mine tailing with municipal solid waste incineration fly ash and ground granulated blast-furnace slag for unfired brick fabrication

Phosphogypsum-based Building Materials: Resource Utilization, Development, and Limitation

Utilization of industrial wastes in non-sintered bricks: microstructure and environmental impacts

Preparation of high-performance lightweight materials based on the phosphogypsum-inorganic material system

Comprehensive Utilization of Blast Furnace Slag, Municipal Sludge and Kaolin Clay in Building Brick Manufacture: Crystalline Transformation, Morphology Observation and Property Assessment

Dredged marine sediments stabilized/solidified with cement and GGBS: Factors affecting mechanical behaviour and leachability