Abstract:Coupled chemical and mechanical phenomena at electrode interfaces largely govern the reversibility and long term stability of lithium ion and lithium metal batteries. A well-known example in lithium ion batteries is the formation of the electrically insulating, ionically conductive, continuous solid electrolyte interface (SEI) on graphitic anodes, which passivates the electrode against further electrochemical reduction of the electrolyte. Unfortunately, this stable passivation does not occur in Si and Li metal anodes. High voltage cathodes are also prone to detrimental interfacial processes, resulting in electrolyte oxidation, gas formation, and transition metal dissolution. In response, a myriad of coating technologies has been developed to mitigate and control these interfacial phenomena and enable next-generation electrodes. These technologies must provide thin, conformal coatings over the entire electrochemically active surface area of the electrode; the coatings must also possess the requisite mechanical properties to accommodate volume dilation due to lithium insertion/extraction. This presentation will describe the development of conformal, compliant polymer thin film coatings for lithium battery electrodes. The polymer thin films are prepared by initiated chemical vapor deposition (iCVD), which provides exquisite control over film composition and morphology by facilitating heterogeneous free-radical polymerization of vinyl monomers with thickness precision on the order of 1 nm. Poly(1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane) (pV4D4) was deposited onto silicon thin film electrodes using iCVD. 25 nm-thick pV4D4 films on Si electrodes improved initial coulombic efficiency by 12.9% and capacity retention over 100 cycles by 64.9% relative to untreated electrodes. PV4D4 coatings also improved rate capabilities, enabling higher lithiation capacity at all current densities. Post-cycling FTIR and XPS showed that pV4D4 inhibited electrolyte reduction and altered the SEI composition, with enrichment in LiF. In another example, thin conformal coatings of perfluorinated polymer were deposited onto battery-grade Cu current collectors to function as an artificial solid electrolyte interface. The effect of the film thickness on Li cycling reversibility was characterized. By galvanostatically cycling Li in an asymmetric Li||Cu cell using 1M LiFSI in a 1:1 (v/v) mixture of dioxolane:dimethoxyethane at 30°C, it was shown that the average coulombic efficiency averaged over 50 cycles increased from 98.36% for bare, untreated Cu to 99.08% for Cu coated with 25 nm of the fluoropolymer. Moreover, the 25 nm coating suppressed interfacial impedance growth on the current collector; the resistance of the coated Cu was 40% lower than the untreated Cu after 100 cycles. The mechanism by which the polymer coating enhances coulombic efficiency and suppresses side reactions will be discussed, along with discussion of the performance in practical anode-free lithium metal batteries.

Surrogate optimization of lithium-ion battery coating process

Analysis of side heavy edge reduction of battery electrode using high speed blade coating process

Impact of Formulation and Slurry Properties on Lithium‐ion Electrode Manufacturing

Application of Deep Learning to Optimize Gradient Porosity Profile for Improved Energy Density of Lithium-Ion Batteries

Slot die coating of lithium-ion battery electrodes: investigations on edge effect issues for stripe and pattern coatings

Surrogate Model Assisted Lithium-Ion Battery Co-Design for Fast Charging and Cycle Life Performances

Scalable Process for Application of Stabilized Lithium Metal Powder in Li-ion Batteries

Experimental and numerical study on flow characteristics of dual‐cavity die based on multi‐objective optimization

Accelerating Battery Electrolyte Design Process Via Closed-Loop Optimization of Simulations and Experiments

(Invited) Lithium Battery Interfacial Engineering with Thin Conformal Polymer Coatings

Scalable Aqueous Battery Electrode Processing Strategy to Improve High C-Rate Capability of Lithium-Ion Battery Electrodes

Self-generated Concentration and Modulus Gradient Coating Design to Protect Si Nano-Wire Electrodes During Lithiation

Design of slurries for 3D printing of sodium-ion battery electrodes

Advancements in Dry Coating for Battery Electrodes: Scalable Extrusion Mixing for Control of Electrode Microstructure and Electrochemical Performance

Surface Coating Engineering of Prelithiation Cathode Additives for Lithium-Ion Batteries

Numerical and experimental investigation on the defect formation in lithium-ion-battery electrode-slot coating

Holistic optimization of lithium-ion battery negative electrode formulation using a combination of theory of mixtures, Box-Behnken matrix, multi-variant analysis and desirability functions of Derringer-Suich

Surface Engineering Based on Conductive Agent Dispersion Uniformity: Strategies toward Performance Consistency of Lithium-Ion Batteries

Multi-objective optimization of liquid cooling system for lithium-ion battery

Feasibility of Cathode Surface Coating Technology for High‐Energy Lithium‐ion and Beyond‐Lithium‐ion Batteries

Multiobjective Optimization Strategy for Enhancing the Efficiency and Quality of Organic Thin-Film Manufacturing with Electrohydrodynamic Atomization Coating