On the influence of local deformation on structural dynamic models of bolted lap joints

Stefan Wischmann,Georg Jacobs,Gregor Höpfner

DOI: https://doi.org/10.1007/s10010-024-00733-7

2024-04-27

Forschung im Ingenieurwesen

Abstract:The acoustic and structural dynamic behavior of technical products—often referred to as Noise, Vibration, and Harshness (NVH) —is an important criterion in customers' purchasing decisions. Therefore, NVH optimization is a crucial goal of the development process. NVH is influenced by dynamic excitations, caused by time-varying forces e.g. in gears or electric machines, as well as the transfer path of sound from the location of excitation to a receiver such as a driver's ear and the sound perception. The behavior of the transfer path is determined by amplification or isolation of structure-borne and airborne sound between the location of the excitation and the location of the receiver. As a result, eigenfrequencies and damping in the transfer path form crucial structural dynamic properties.

engineering, mechanical, multidisciplinary

What problem does this paper attempt to address?

### Problems Addressed by the Paper

This paper aims to study the impact of local deformation on the dynamic model of bolted lap joints. Specifically, the paper focuses on how to select an appropriate spatial discretization method to accurately model the dynamic behavior of the joint in elastic multibody simulation (eMBS), particularly considering the local deformation of the joint surface.

### Background and Motivation

Noise, Vibration, and Harshness (NVH) are important characteristics of technical products and significantly influence consumer purchasing decisions. Therefore, optimizing the NVH performance of products is a key objective in the development process. NVH performance is affected by dynamic excitations (such as time-varying forces in gears or motors) and the transmission path of sound from the excitation point to the reception point (such as the driver's ear). The behavior of the transmission path determines the amplification or isolation of structure-borne and airborne sound between the excitation and reception points, thus forming the key structural dynamic properties of the transmission path.

In joint structures, friction between joint surfaces is one of the main influencing factors, especially in the high-frequency range, where local deformation significantly affects the friction behavior of the joint. However, in eMBS models, the deformation of the joint part is usually simplified to the relative motion between a few concentrated points, which may lead to model errors. Therefore, selecting an appropriate spatial discretization method is crucial for improving the quality of eMBS models.

### Research Methods

1. **Selecting an Appropriate Physical Model**: The paper selects the Reduced Iwan model to represent the stiffness and damping behavior of the joint, as this model can simulate tangential damping and amplitude-dependent stiffness under micro-slip and macro-slip conditions.

2. **Defining Appropriate Spatial Discretization**: The paper proposes a stiffness criterion-based method to determine spatial discretization. By calculating the stiffness values of the joint surface nodes, the suitability of different discretization schemes is evaluated. If the stiffness value of a node is high, the error introduced by simplifying the node's motion to a concentrated force application point is smaller.

3. **Parameter Identification**: Parameter identification is performed by fitting the quasi-static hysteresis curves of the Reduced Iwan elements to the quasi-static hysteresis curves of the finite element model (FE model). First, a single joint element is isolated through the FE model, then normal loads are applied, and hysteresis curves under different displacement/angle amplitudes are obtained through translational and rotational motions. Finally, a gradient optimization algorithm is used to optimize the parameters of the Reduced Iwan elements.

### Application Example

The paper uses the Brake Reuß Beam (BRB) as an example to verify the proposed method. The BRB consists of two freely suspended beam elements connected by three M8 bolts. Excitation is applied using a vibration table, and the response is measured using a laser Doppler vibrometer (LDV). Experimental results show that as the excitation amplitude increases, the resonance frequency decreases, and the damping increases. These results are used to validate the FE model and serve as the basis for eMBS modeling.

### Conclusion

The method proposed in the paper can accurately model the dynamic behavior of joint structures in an eMBS environment by selecting an appropriate spatial discretization method, reducing model errors. Experimental results show that the error between the eMBS model established using this method and the measurement results is less than 1 dB, indicating high accuracy.