Abstract:A new lower tungsten divertor has been developed and installed in the EAST superconducting tokamak to replace the previous graphite divertor with power handling capability increasing from <2 MW m−2 to ∼10 MW m−2, aiming at achieving long-pulse H-mode operations in a full metal wall environment with the steady-state divertor heat flux of ∼10 MW m−2. A new divertor concept, ‘corner slot’ (CS) divertor, has been employed. By using the ‘corner effect’, a strongly dissipative divertor with the local buildup of high neutral pressure near the corner can be achieved, so that stable detachment can be maintained across the entire outer target plate with a relatively lower impurity seeding rate, at a separatrix density compatible with advanced steady-state core scenarios. These are essential for achieving efficient current drive with low-hybrid waves, a low core impurity concentration and thus a low loop voltage for fully non-inductive long-pulse operations. Compared with the highly closed small-angle-slot divertor in DIII-D, the new divertor in EAST exhibits the following merits: (1) a much simpler geometry with integral cassette body structure, combining vertical and horizontal target plates, which are more suitable for actively water-cooled W/Cu plasma facing components, facilitating installation precision control for minimizing surface misalignment, achieving high engineering reliability and lowering the capital cost as well; (2) it has much greater flexibility in magnetic configurations, allowing for the position of the outer strike point on either vertical or horizontal target plates to accommodate a relatively wide triangularity range, δ l = 0.4–0.6, thus enabling to explore various advanced scenarios. A water-cooled copper in-vessel coil has been installed under the dome. Five supersonic molecular beam injection systems have been mounted in the divertor to achieve faster and more precise feedback control of the gas injection rate. Furthermore, this new divertor allows for double null divertor operation and slowly sweeping the outer strike point across the horizontal and vertical target plates to spread the heat flux for long-pulse operations. Preliminary experimental results demonstrate the ‘corner effect’ and are in good agreement with simulations using SOLPS-ITER code including drifts. The EAST new divertor provides a test-bed for the closed divertor concept to achieve steady-state detachment operation at high power. Next step, a more closed divertor, ‘sharp-cornered slot’ divertor, building upon the current CS divertor concept, has been proposed as a candidate for the EAST upper divertor upgrade.

Optimizing control for strike point sweeping using lower divertor coil in EAST

Divertor Power Deposition Control and ELM Mitigation with Supersonic Molecular Beam Injection in the EAST Tokamak

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Long-pulse H-mode operation with stored-energy monitoring for detachment feedback control with a new lower tungsten divertor in EAST

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Divertor Impurity Seeding with a New Feedback Control Scheme for Maintaining Good Core Confinement in Grassy-Elm H-mode Regime with Tungsten Monoblock Divertor in EAST

Experimental study of elm control by varying toroidal rotation with ctr-nbi on east d

Effects of strike point location on the divertor particle and energy flux decay widths on EAST by experiment and SOLPS modeling

Design of EAST lower divertor by considering target erosion and tungsten ion transport during the external impurity seeding

1 EXD / P 3-14 Recent Advances in Long Pulse Divertor Operations on EAST

Advances in the Long-Pulse Steady-State High Beta H-mode Scenario with Active Controls of Divertor Heat and Particle Fluxes in EAST

Integrated ELM and divertor power flux control using RMPs with low input torque in EAST in support of the ITER research plan

Impurity control study of radiative tungsten divertor in EAST tokamak

Experiences and lessons from the mitigation of leading edge induced melting on actively cooled ITER-like W/Cu monoblocks for divertor target in EAST

Effects of divertor geometry on detachment and core plasma performance with impurity seeding in EAST

Optimisation of the poloidal field system for advanced divertor configurations in STEP

Fully Active Cooled In-vessel Components of EAST Tokamak

Recent EAST Experimental Results and Systems Upgrade in Support of Long-Pulse Steady-State Plasma Operation

Decoupled magnetic control of spherical tokamak divertors via vacuum harmonic constraints

Disconnection of edge coherent mode between the outer midplane and divertor target in EAST H-mode plasma

Divertor Detachment and Asymmetry in H-mode Operation with an ITER-like Tungsten Divertor in EAST