Abstract:Understanding and controlling the crystallization process is critical to achieving high‐quality perovskite films and efficient solar cells. Herein, we identified that one key issue in the formation of formamidinium lead iodide (FAPbI3) defects is the participation of the intermediates in the crystallization process. A comprehensive picture of structural and carrier evolution during crystallization was demonstrated using a combination of in situ grazing‐incidence wide‐angle X‐ray scattering, UV‐Vis, and photoluminescence spectroscopies. Three crystallization stages were registered for the commonly observed conversion pathway of precursors – δ‐FAPbI3 intermediate – α‐FAPbI3, during which the spontaneous generation of defects was found. We found that a hydrogen sulfate‐based ionic liquid additive enabled the phase conversion pathway of precursors – solvated intermediates – α‐FAPbI3, during which the spontaneous generation of δ‐FAPbI3 can be effectively circumvented. Both growth kinetics at the initial crystallization stage and the following recrystallization of α‐FAPbI3 were significantly prolonged because of the additional exchange process between solvents and FA+, which resulted in the self‐elimination of defects during crystallization. Therefore, the improved crystallization dynamics led to larger grain sizes and fewer defects within thin films. The improved perovskite crystallization dynamics finally transformed into high‐performance solar cells under one‐sun illumination (AM 1.5 G) with efficiency as high as 25.14% at 300 K. These cells delivered a PCE of 26.12% at 240 K, which might open up a new era of application of this emerging photovoltaic technology to low‐temperature environments such as near‐space and polar regions. This article is protected by copyright. All rights reserved

Overcoming Microstructural Defects at the Buried Interface of Formamidinium-Based Perovskite Solar Cells

Defect Passivation in CH3NH3PbI3 Films Using Alkali Metal Fluoride Additives for Highly Efficient Perovskite Solar Cells

Buried Interfaces in Halide Perovskite Photovoltaics

Defect Engineering at Buried Interface of Perovskite Solar Cells

Reconstructing Subsurface Lattice for Stable Perovskite Photovoltaics

Au Nanocluster Assisted Microstructural Reconstruction for Buried Interface Healing for Enhanced Perovskite Solar Cell Performance

Shallow Iodine Defects Accelerate the Degradation of α-Phase Formamidinium Perovskite

In situ self‐elimination of defects via controlled perovskite crystallization dynamics for high‐performance solar cells

Minimizing buried interfacial defects for efficient inverted perovskite solar cells

Enhancing the Efficiency and Stability of Inverted Formamidinium-Cesium Lead-Triiodide Perovskite Solar Cells through Lewis Base Pretreatment of Buried Interfaces

Optimizing The Buried Interface in Flexible Perovskite Solar Cells to Achieve Over 24% Efficiency and Long‐Term Stability

Halides‐enhanced buried interfaces for stable and extremely low‐voltage‐deficit perovskite solar cells

Defect suppression and energy level alignment in formamidinium-based perovskite solar cells

Revealing the impact of buried interfacial nanostructure in perovskite solar cells

Quantifying the Interface Defect for the Stability Origin of Perovskite Solar Cells

Amphoteric Ion Bridged Buried Interface for Efficient and Stable Inverted Perovskite Solar Cells

Target Therapy for Buried Interface Enables Stable Perovskite Solar Cells with 25.05% Efficiency

Engineering the buried interface in perovskite solar cells via lattice-matched electron transport layer

Insight into structure defects in high-performance perovskite solar cells

Elimination of unstable residual lead iodide near the buried interface for the stability improvement of perovskite solar cells

Buried-Interface Engineering of Conformal 2D/3D Perovskite Heterojunction for Efficient Perovskite/Silicon Tandem Solar Cells on Industrially Textured Silicon