Abstract:Kapton film is a polymeric material widely used on low-Earth-orbit (LEO) spacecraft surfaces. In the LEO environment, atomic oxygen (AO) is spaceflight materials' most destructive environmental factor. The erosion mechanism of AO on Kapton films has long been an important issue, where the parameter dependence of the AO effect has received increasing attention. Studies of AO energy and cumulative flux have been extensively carried out, while the influence mechanism of the incidence angle and flux density is not fully understood. The AO incidence angle and flux density in space are diverse, which may cause different damage effects on aerospace materials. In this paper, the dependence of the incidence angle and flux density in the damaging effect of AO on Kapton films was investigated using ground-based AO test technology and the reactive molecular dynamics (ReaxFF MD) simulation technique. Firstly, the ground-based experiment obtained the mass loss data of Kapton films under the action of AO with a variable incidence angle and flux density. Then, the mass loss, temperature rise, product, and erosion yield of Kapton during AO impact with different incidence angles and dose rates were calculated using the ReaxFF MD method. The influences of the incidence angle and flux density on the damage mechanism of the AO effect were discussed by comparing the simulation and test results. The results show that the AO effect in the lower incidence angle range (0-60°) is independent of the incidence angle and depends only on the amount of impacted atomic oxygen. AO in the higher incidence angle range (60-90°) has a surface stripping effect, which causes more significant mass loss and a temperature rise while stripping raised macromolecules from rough surfaces, and the erosion effect increases with the increasing incidence angle and amount of impacted atomic oxygen. There is a critical value for the influence of flux density on the AO effect. Above this critical value, AO has a reduced erosive capacity due to a lower chance of participating in the reaction. The amount of each main product from the AO effect varies with the incidence angle and flux density. Nonetheless, the total content of the main products is essentially constant, around 70%. This work will contribute to our understanding of the incidence angle and flux density dependence of the AO effect and provide valuable information for the development of standards for ground simulation tests.

Erosion evolution and mass loss of polyimide in AO environment using 3D Monte Carlo method

Prediction of erosion characteristics of polyimide with different defect shape pairs based on Monte Carlo method

Damage and degradation of mechanical properties of polyimide-based materials under atomic oxygen attack: A molecular dynamics simulation study

Reactive molecular dynamics simulation on the disintegration of Kapton and Upilex-S during atomic oxygen impact

Study on the Effects and Mechanism of Temperature and AO Flux Density in the AO Interaction with Upilex-S Using the ReaxFF Method

Mechanism Analysis and Potential Applications of Atomic Oxygen Erosion Protection for Kapton-Type Polyimide Based on Molecular Dynamics Simulations

Mechanisms of Atomic Oxygen Erosion in Fluorinated Polyimides Investigated by Molecular Dynamics Simulations

Resistance of amorphous TiAlCrZrSi/polyimide high entropy alloy films to atomic oxygen erosion

Mesoscopic modeling of mechanical erosion for the ablation-erosion behavior of 3D C/C composites

Studies on the Erosion Mechanism of Kapton and Its Protective Effect

A reactive molecular dynamics simulation of the atomic oxygen impact on poly(p-phenylene-terephthalamide)

Dependence of Incidence Angle and Flux Density in the Damage Effect of Atomic Oxygen on Kapton Film

The effects of atomic oxygen and ion irradiation degradation on multi-polymers: A combined ground-based exposure and ReaxFF-MD simulation

An Impact Energy Erosion Model with an Energy Allocation Rule for the Discrete Element Method

Reactive Molecular Dynamics Study of the Mechanism and Effect of Various Protective Coatings on the Protection of Polyimide Antierosion from Atomic Oxygen

Analysis of thermochemical ablation and mechanical erosion of C/C composites based on macro-meso-scale numerical simulation methods

A mesoscopic model of mechanical erosion for the characterization of ablation behavior of C/C woven composites

An Erosion Model for the Discrete Element Method

Atomic oxygen degradation of a fluorine-containing colorless polyimide

Monte Carlo/molecular Dynamics Simulation on Melting and Evaporating Processes of Material Due to Laser Irradiation

Property of Protection against Simultaneous Action between Atomic Oxygen Erosion and Ultraviolet Irradiation by MIL-53(Al) Coating