Abstract:Wire-based laser directed energy deposition (LDED) technology is an attractive and efficient additive manufacturing technology, which shows great potential in the process of manufacturing high-value engineering components. However, the thermal effect will lead to a large amount of residual tensile stress in the components, and the large crystal structures after solidification seriously affects the tensile performance. The pursuit of high mechanical properties in additive manufacturing components have prompted researchers to seek new strengthening process to produce high-strength components. Therefore, in this paper, laser shock peening (LSP) composite wire-based LDED were used for the additive manufacturing of 17-4 PH stainless steel under the specified experimental conditions, and the effects of LSP on microstructure evolution, microhardness, and tensile properties of wire-based LDED components were systematically studied. Results showed that uniform grains with an average size of 2.31 mu m were generated on the top surface of specimen due to the ultra-high plastic strain induced by LSP shock wave. The size of hierarchical martensitic units shows varying degrees of reduction after LSP treatment, which is shown by the width decrease of packet, block and lath. Dynamic recrystallization caused by rearrangement and annihilation of high-density dislocations promoted the grain refinement. Meanwhile, the residual stress was completely converted from tensile state into compressive state with a maximum value of 425 MPa, and the microhardness was also enhanced to a peak value of 432 HV. In addition, we observed that the high-density dislocation environment created by LSP treatment promoted the further precipitation, and the aggregation phenomenon of precipitates was observed in the dense dislocation area. Furthermore, the tensile strength and elongation of LSP treated specimen were improved significantly, which was attributed to the combined effects of grain refinement, introduction of dislocation structures, precipitation strengthening and gradient residual compressive stress. In summary, laser hybrid additive manufacturing technology provides a new idea and method for the production of high-performance precipitation hardening stainless steel components.

Iso-Material Manufactured 17-4PH Stainless Steel to Enhance the Nano-indentation, Corrosion, and Cavitation Erosion Behavior

Effect of Residual Stress and Phase Constituents on Corrosion-Cavitation Erosion Behavior of 304 Stainless Steel by Iso-Material Manufacturing of Laser Surface Melting

Iso-material manufacturing of 304 stainless steel: Microstructure, corrosion-cavitation erosion synergistic behaviour

Femtosecond Laser Treatment for Improving the Corrosion Resistance of Selective Laser Melted 17-4PH Stainless Steel

Microstructure–Hardness–Corrosion Performance of 17–4 Precipitation Hardening Stainless Steels Processed by Selective Laser Melting in Comparison with Commercial Alloy

Microstructural and Mechanical Characterization of Selective Laser Melted 17-4 PH Stainless Steel: Effect of Laser Scan Strategy and Heat Treatment

Tensile Properties and Microstructural Evolution of 17–4 PH Stainless Steel Fabricated by Laser Hybrid Additive Manufacturing Technology

Microstructure and Properties of Laser Surface Melted AISI 316L Stainless Steel

Enhancing Wear Resistance and Erosion Wear Performance of Laser Additive Manufactured 17-4PHss through Solution Aging Treatment

Mechnical properties of 17-4PH stainless-steel at various laser sintering process parameters

Improving mechanical properties and isotropy of laser DED 17-4 PH stainless steel by combining ultrasonic vibration

Effect of powder chemical composition on the as-built microstructure of 17-4 PH stainless steel processed by selective laser melting

Characterization of Microstructural Anisotropy in 17–4 PH Stainless Steel Fabricated by DMLS Additive Manufacturing and Laser Shot Peening

Effect of Process Parameters on Density and Mechanical Behaviour of a Selective Laser Melted 17-4PH Stainless Steel Alloy

Influence of powder particle size distribution on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by selective laser melting

Microstructural, Mechanical, and Electrochemical Corrosion Properties of Extrusion Additive Manufactured 17-4 Precipitation Hardenable Stainless Steel

Microstructure and Corrosion Resistance of Stainless Steel Manufactured by Laser Melting Deposition

The Effect of Varying Parameters of Laser Surface Alloying Post-Treatment on the Microstructure and Hardness of Additively Manufactured 17-4PH Stainless Steel

Enhance corrosion resistance of 304 stainless steel using nanosecond pulsed laser surface processing

Effect of laser remelting processing on microstructure and mechanical properties of 17-4 PH stainless steel during laser direct metal deposition

Microstructural Evolution and Mechanical Behavior of Additive Manufactured 17-4 PH Steel with a Periodic Layer Structure