Abstract:Abstract Additive manufacturing (AM) is a developing manufacturing technology, which provides excellent attributes compared to other manufacturing techniques. However, one of the critical challenges is the presence of defects that hinder the mechanical properties of the parts, particularly the fatigue life. Experimental understanding of fatigue is a cumbersome process. Therefore, numerical prediction based on specified conditions (such as porosity and applied load) can be an alternative to experimental analysis at the design stage of AM parts. In this study, elastic–plastic finite element analysis (FEA) is performed to obtain the stress distribution around pores, and their resultant effect on fatigue life for L-PBF (laser powder bed fusion) produced AlSi10Mg alloy samples. The stress field is calculated for both single and multiple pore models, where stress concentration is evaluated as a function of the pore’s location and its size. It is found that both pore location and size affect the stress field; however, location effects dominate over pore size. For the same remote applied stress level, the stress concentration around the pore increases with an increase in pore size, and the local maximum stress occurs near the pores that are closest to the surface. The current study also evaluates the relative effect of porosity fraction, average pore size, and location. It is found that the magnitude and sensitivity of stress concentration are hierarchically controlled by porosity location, pore size, and porosity density. A multi-scale finite element (FE) model is proposed based on inherent porosity data measured using Computed Tomography (CT) to predict overall fatigue life. The fatigue cycles are calculated using the rainflow counting algorithm in FE Safe using the stress–strain data obtained from the proposed FEA model. Using the proposed model, it is possible to generate S–N curves for any loading condition for a given porosity condition (porosity density and average pore size). The S–N curve results obtained from the FE model are compared to the experimental observations. The predicted fatigue life shows approximately 5% error with experimental results at high stress loading conditions. However, the proposed model overpredicts the fatigue life at low stress loading by almost 30%.

Influence of surface porosity on fatigue life of additively manufactured ASTM A131 EH36 steel

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Analysing the effect of defects on stress concentration and fatigue life of L-PBF AlSi10Mg alloy using finite element modelling

A comprehensive study on the influence of the scan pattern in two porosity levels and surface roughness on the fatigue behavior of laser powder bed fusion manufactured specimens made of steel H13

Understanding the fatigue behaviour of Ti–6Al–4V manufactured via various additive processes

High Cycle Fatigue Behavior of 316L Steel Fabricated by Laser Powder Bed Fusion: Effects of Surface Defect and Loading Mode

Surface condition driven fatigue performance of laser powder bed fusion H13 steel

The Influence of the Ratio of Circumference to Cross-Sectional Area of Tensile Bars on the Fatigue Life of Additive Manufactured AISI 316L Steel

Fatigue behavior of selective laser melted 316L stainless steel: experiments and modeling

Influence of Porosity on Fatigue Behaviour of 18Ni300 Steel SLM CT Specimens at Various Angles

Crack growth-based life prediction for additively manufactured metallic materials considering surface roughness

Microstructure evolution, failure mechanism and life prediction of additively manufactured Inconel 625 superalloy with comparable low cycle fatigue performance

Surface Treatment of Powder-Bed Fusion Additive Manufactured Metals for Improved Fatigue Life

Microstructure and mechanical properties of ASTM A131 EH36 steel fabricated by laser aided additive manufacturing

Fatigue life prediction of additively manufactured AlSi10Mg based on surface roughness and residual stress

Numerical simulation of surface roughness effects on low-cycle fatigue properties of additively manufactured titanium alloys

Dissipative and thermal aspects in cyclic loading of additive manufactured AISI 316L

Predicting the Effect of Surface Waviness on Fatigue Life of a Wire + Arc Additive Manufactured Ti-6Al-4V Alloy

Enhancement of fatigue resistance of additively manufactured 304L SS by unique heterogeneous microstructure

The potency of defects on fatigue of additively manufactured metals