Abstract:Due to its hydroxyl terminal groups, Poloxamer ® 407 (P407), a commercially available poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer can be used as macrodiol for the synthesis of high molecular weight amphiphilic poly(ether urethane)s (PEUs). This work was aimed at studying the effect of P407 purification by removing PEO-PPO diblock copolymer by-products on the chemical properties of PEU polymer and the physical properties of PEU hydrogels. Removal of PEO-PPO diblock copolymers (P407_P) was found to preserve the thermo-responsiveness of resulting hydrogels, although slightly lower gelation onset temperature (T onset ) was found for P407_P (15.3°C) vs . P407 (16.7°C) hydrogels (25% w/V) as assessed through temperature ramp test. P407 and P407_P were then reacted with 1,6-diisocyanatohexane and 1,4-cyclohexanedimethanol to synthesize two different PEUs, coded as CHP407 and CHP407_P, respectively. Lower Number Average Molecular Weight ( M n ̄ ) and higher polydispersity Index (D) was measured for CHP407 ( M n ̄ : 34 kDa, D: 1.6) respect to CHP407_P ( M n ̄ : 40 kDa, D: 1.4) as a consequence of macrodiol purification. CHP407_P hydrogels formed bigger micelles (43.9 ± 4.1 nm vs . 28.7 ± 4 nm) while showed similar critical micellar temperatures (22.1°C vs . 21.6°C) respect to CHP407 formulations. Sol-to-gel transition of CHP407 and CHP407_P hydrogels was similar while CHP407_P gelation time at 37°C was longer as assessed by tube inverting test. The rheological analysis showed slightly lower T onset for CHP407_P hydrogels (15% w/V), probably due to larger micelle size, promoting micellar assembly. However, CHP407_P hydrogels showed a significantly lower critical strain than CHP407 hydrogels, as assessed by strain sweep test, suggesting their higher brittleness due to a lower density of intermicellar bridge chains. Nano-scale hydrogel characterization by Low-Field Nuclear Magnetic Resonance spectroscopy supported previous findings, showing lower spin-spin relaxation time (i.e., 1,259 ms) for CHP407_P than for CHP407 hydrogels (i.e., 1,560 ms) at 37°C, which suggested the formation of a more tightly packed network for CHP407_P than CHP407 hydrogel. Finally, lower swelling capability and resistance against dissolution were measured for CHP407_P hydrogels. Overall, the here‐reported results suggested that the heterogeneous structure in the CHP407 hydrogel network caused by the presence of diblock copolymer-based macrodiols improved PEU hydrogel properties in light of their applicability in the biomedical field.

Synthesis and characterization of polyHIPEs using a polymerizable polyurethane macromolecular surfactant

Toward Maximizing the Mechanical Property of Interconnected Macroporous Polystyrenes Made from High Internal Phase Emulsions.

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

One-Pot Interfacial Polymerization to Prepare Polyhipes with Functional Surface

Pushing the Mechanical Strength of PolyHIPEs Up to the Theoretical Limit Through Living Radical Polymerization

Water-in-Oil emulsion templated polyurethanes with uniform porosity

Synthesis of High-Toughness Waterborne Polyurethane Utilizing Self-Emulsifying CO2-based Polyols

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Porous PS- and PMMA-based polymeric monoliths prepared by PEO-PS block copolymers stabilized High internal phase emulsion templates

Mechanism of Interconnected Pore Formation in High Internal Phase Emulsion-Templated Polymer

Hierarchical polymerized high internal phase emulsions synthesized from surfactant-stabilized emulsion templates

Complex High-Internal Phase Emulsions that can Form Interfacial Films with Tunable Morphologies

Acrylic Acid “Reversed” PolyHIPEs

Influence of crosslinker on the properties of terpene‐based poly(high internal phase emulsion)s

Morphology and properties of high molecular weight polyisobutylene and thermoplastic polyurethane elastomer

Synthesis, Characterization and Biocompatibility of Biodegradable Elastomeric Poly(ether-ester Urethane)s Based on Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) and Poly(ethylene Glycol) Via Melting Polymerization

Synthesis and Properties of Polystyrene-Based Polyhipes Reinforced with Quadruple Hydrogen Bond Functionality

Cellulose-based, flexible polyurethane polyHIPEs with quasi-closed-cell structures and high stability for thermal insulation

Interconnected Macroporous Polymers Synthesized from Silica Particle Stabilized High Internal Phase Emulsions

Using Poloxamer® 407 as Building Block of Amphiphilic Poly(ether urethane)s: Effect of its Molecular Weight Distribution on Thermo-Sensitive Hydrogel Performances in the Perspective of Their Biomedical Application

Study on Synthesis and Properties of Novel HTPB/PEG Polyurethane Copolymers