Abstract:Laser-textured surfaces enabling reversible wettability switching and improved optical properties are gaining importance in cutting-edge applications, including self-cleaning interfaces, tunable optical lenses, microfluidics, and lab-on-chip systems. Fabrication of such surfaces by combining nanosecond-laser texturing and low-temperature annealing of titanium Ti-6Al-4V alloy was demonstrated by Lian et al. in ACS Appl. Mater. Inter. 2020, 12 (5), 6573-6580. However, it is difficult to agree with (i) their contradictory explanation of the wettability transition due to low-temperature annealing and (ii) their theoretical description of the optical behavior of the laser-textured titanium surface. This comment provides an alternative view-supported by both experimental results and theoretical investigation-on how the results by Lian et al. could be interpreted more correctly. The annealing experiments clarify that controlled contamination is crucial in obtaining consistent surface wettability alterations after low-temperature annealing. Annealing of laser-textured titanium at 100 °C in contaminated and contaminant-free furnaces leads to completely different wettability transitions. Analysis of the surface chemistry by XPS and ToF-SIMS reveals that (usually overlooked) contamination with hydrophobic polydimethylsiloxane (PDMS) may arise from the silicone components of the furnace. In this case, a homogeneous thin PDMS film over the entire surface results in water repellency (contact angle of 161° and roll-off angle of 15°). In contrast, annealing under the same conditions but in a contaminant-free furnace preserves the initial superhydrophilicity, whereas the annealing at 350 °C turns the hydrophobicity "off". The theoretical calculations of optical properties demonstrate that the laser-induced oxide layer formed during the laser texturing significantly influences the surface optical behavior. Consequently, the interference of light reflected by the air-oxide and the oxide-metal interfaces should not be neglected and enables several advanced approaches to exploit such optical properties.

Fabrication of antireflection surfaces with superhydrophobic property for titanium alloy by nanosecond laser irradiation

Fabrication of Modifier-Free Superhydrophobic Surfaces with Anti-Icing and Self-Cleaning Properties on Ti Substrate by Anodization Method

Superhydrophobic Surface Preparation and Wettability Transition of Titanium Alloy with Micro/Nano Hierarchical Texture

Anti-reflection Coating at 550 Nm Fabricated by Atomic Layer Deposition

Fabrication of Superhydrophobic Ti–6Al–4V Surfaces with Single-Scale Micotextures by using Two-Step Laser Irradiation and Silanization

Fabrication of superhydrophilic or superhydrophobic self-cleaning metal surfaces using picosecond laser pulses and chemical fluorination

Nanostructured Superhydrophobic Titanium-Based Materials: A Novel Preparation Pathway to Attain Superhydrophobicity on TC4 Alloy

Laser Fabrication of Titanium Alloy-Based Photothermal Responsive Slippery Surface

Fast fabrication of superhydrophobic Ti-6Al-4V surface using Q-switched nanosecond pulsed laser at 1064 nm and cyclohexane

Nanostructuring of laser textured surface to achieve superhydrophobicity on engineering metal surface

Superhydrophobic Surface of Ti6Al4V using Direct Nanosecond Laser Texturing

Progress on Ultrafast Laser Fabricating Metal Surface Micro-Nano Antireflection Structures

Preparation of Superhydrophobic Surface on Titanium Alloy via Micro-Milling, Anodic Oxidation and Fluorination

Fabrication and droplet impact performance of superhydrophobic Ti6Al4V surface by laser induced plasma micro-machining

Construction of Robust Hierarchical Micro-nanostructure by Laser Irradiation and Hydrothermal Treatment on Titanium Alloy for Superhydrophobic and Slippery Surfaces

Hierarchical Micro/Nanostructures with Anti-Reflection and Superhydrophobicity on the Silicon Surface Fabricated by Femtosecond Laser

Fabrication of Titanium-Based Microstructured Surfaces and Study on Their Superhydrophobic Stability

Influence of laser fluences and scan speeds on the morphologies and wetting properties of titanium alloy

Nanosecond Laser Fabrication of Novel Micro-/Nanostructured Metal Surfaces: A Dual-Functional Supersurface Combining Antireflectivity and Superhydrophobic Properties

Comment on "Bioinspired Reversible Switch between Underwater Superoleophobicity/Superaerophobicity and Oleophilicity/Aerophilicity and Improved Antireflective Property on the Nanosecond Laser-Ablated Superhydrophobic Titanium Surfaces"

Durable self-cleaning anti-fog and antireflective titanium-based micro-nano structures on glass by laser marker ablation