Abstract:The interaction between nanosecond laser and glass is complicated, and defects such as micro-cracks and fractures are prone to be generated during laser scribing. Acoustic emission (AE) technique is applied in this paper to monitor laser scribing of float glass. Strong consistency between AE signals and width of laser ablation area is found. With laser power increasing from 11.2 to 26.9 W, root mean square (RMS) values increase from 0.160 to 0.634 V, and width of heat affected zone (HAZ) increase from 12.396 to 53.711 μm\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$${\upmu }\text{m}$$\end{document}. Correlation between AE signals and laser scribing quality is investigated by characteristic analysis. When scanning speed is kept constant (200 mm/s) and laser power is gradually increasing from 11.2 to 24.2 W, RMS values and MARSE are increasing (0.3–1.2 V, 600–1500 correspondingly), and scribing quality is declining continuously (WCWG\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\frac{{W}_{C}}{{W}_{G}}$$\end{document} increase from 0 to 0.343). Time-frequency spectrum analysis by CWT could be applied in defects diagnosis. Three prominent frequency bands contents (150 ~ 180 kHz, 200 ~ 250 kHz, and 280 ~ 320 kHz) were generated during laser scribing process. Higher frequency bands contents (200 ~ 250 kHz, and 280 ~ 320 kHz) are demonstrated to reflect defects by analyzing distribution characteristic of frequency contents. Intensity of higher frequency compositions is vigorous (≥ 0.5) when there are defects, while less than 0.5 with no defects.

Crack growth analysis of ultraviolet nanosecond laser scanning glass with acoustic emission

Reference-free Crack Detection and Localization by Nonlinear Laser Ultrasonic.

A Study of Inner Crack Testing with the Laser Phased Array Method.

A novel monitoring method of nanosecond laser scribing float glass with acoustic emission

Numerical Study for Surface-breaking Crack Detection on A Cylinder Using Laser-generated Ultrasound

Detecting features of defect metal based on laser ultrasonic technique

An Experimental Analysis for Damage Monitoring in Glass Fiber/Epoxy Composites During Fatigue Tests by Acoustic Emission

Quantitative Detection of Small Crack by Nonlinear Laser Ultrasonics

Study on the Interaction Mechanism of Laser-Generated Rayleigh Waves and Subsurface Inclined Cracks

Numerical Simulation of the Interaction of Laser-Generated Rayleigh Waves with Subsurface Cracks

Quantitative Estimation of Crack on or Near Surface Using Laser-Ultrasonic Surface Wave: Numerical Simulation

Quantitative characterization of laser ultrasonic based on energy loss and resonance phenomenon

Crack Formation Detection during Ultra-Fast Laser Beam Machining of Alumina Ceramic Based on Acoustic Emission Signals

Laser induced micro-cracking of Zr-based metallic glass using 1011 W/m2 nano-pulses

Quantitative Detection of Lateral Subsurface Cracks Based on Laser-Generated Rayleigh Waves in the Frequency Domain

Numerical Study of Length and Angle Gauging for Subsurface-Inclined Cracks Based on Reflected Surface Waves with Laser Ultrasonic Technique

Intermittent in-situ high-resolution X-ray microscopy of 400-nm porous glass under uniaxial compression: study of pore changes and crack formation

Laser cutting sandwich structure glass–silicon–glass wafer with laser induced thermal–crack propagation

Crack-Free Laser Processing Of Glass Substrate And Its Mechanisms

Crack suppression of glass welding by ultrafast laser without optical contact based on light modulation

Damage morphology and mechanism in ablation cutting of thin glass sheets with picosecond pulsed lasers