Abstract:The investigation of frictional pressure drops in wire-wrapped bundles at low flow velocities is crucial for thermal-hydraulic studies of sodium-cooled fast reactor cores. This study aims to refine empirical formulas for predicting friction factors in wire-wrapped bundles by addressing their limitations in accurately calculating friction factors during transition regime. By analyzing existing empirical formulas and meticulously observing frictional pressure drop experiments conducted under low-flow conditions that reported in the literature, the study proposes and demonstrates the mechanism of the laminar-to-transitional regime transition in wire-wrapped bundles. Additionally, experimental research was conducted on the frictional pressure drop of a 37-rod wire-wrapped bundle. A novel high-precision differential pressure measurement technique, the photographic liquid column manometer, was employed to enhance frictional pressure drop measurement accuracy. This innovative method achieves a measurement uncertainty of less than 2 Pa within a range of 0 to 300 Pa. The mass flow rate of the fluid was measured and converted to obtain the flow velocity through the assembly, further improving the accuracy of flow velocity measurements. The analysis and experiments reveal that the transition from the laminar to transitional regime does not occur uniformly but initiates locally in certain subchannels before spreading across the assembly as flow velocity increases. Significant increases in the frictional pressure drop occur only after a sufficient number of subchannels have undergone transition. This perspective is supported by extensive existing literature, which report that in assemblies with fewer rod bundles, smaller P/D and H/D values, and constructed from hard metal materials such as stainless steel, the friction factor at the initial stage of the transitional regime shows a significant increase or remains constant with increasing Reynolds number. Under these conditions, the high consistency of the P/D ratio within the assembly causes the fluid to transition within a narrow range of flow velocities, leading to a marked increase in the friction factor with Reynolds number. The research results also indicate that the prediction accuracy of the critical Reynolds number for the laminar-to-transitional flow transition significantly impacts the calculation accuracy of empirical formulas at low flow velocities. Formulas using smaller predicted values of the critical Reynolds number show better agreement between predicted values and the measured results in this study. Therefore, the study recommends adopting smaller critical Reynolds numbers and interpolation indices in empirical formulas to facilitate an early onset and smooth transition of laminar-to-transitional regime behavior in friction factors, thereby improving the accuracy of calculated friction factors.

Advancing performance of a predictive model for pressure drop of wire gauze corrugated sheet structured packings in deep vacuum applications

Predicting the Pressure Drop of Corrugated Sheet Structured Packings in Deep Vacuum Applications

Multi-scale study of wet pressure drop model for a novel structured wire gauze packing

Micro-scaling numerical model coupled with experimental validation of the pressure drop for dense wire mesh

A Differential Pressure Sensor Coupled with Conductance Sensors to Evaluate Pressure Drop Prediction Models of Gas-Water Two-Phase Flow in a Vertical Small Pipe

A mechanistic model of pressure drop in structured packing

Dry Pressure Drop Prediction within Montz-Pak Packing with Varied Inclination Angles Using CFD Simulation

CFD Simulation of Flow and Mass Transfer in Structured Packing Distillation Columns

Experimental and numerical study of mass transfer efficiency in new wire gauze with high capacity structured packing

A novel model of pressure drop for airflow penetrating randomly packed cylindrical particles

A mathematical model for predicting the pressure drop in a rotating cavity with a tubed vortex reducer

Theoretical and Experimental Study of Dry Scroll Vacuum Pump

Prediction Model for Pressure Drop in Venturi Scrubbers

PREDICTION OF VOID FRACTION AND PRESSURE DROP FOR UPWARD GAS-LIQUID TWO-PHASE FLOW THROUGH VERTICAL CONCENTRIC ANNULUS

Validation of numerical models for prediction of pressure drop in high capacity long distance lignite fly ash pneumatic conveying

Validation for CFD Simulation in Rod Bundles with Split-Vane Spacer Grids Based on LDA Measurement

Experimental Study on Frictional Pressure Drop Characteristics of Wire-wrapped Bundles in Transition Flow

A General Pressure Drop Model Based on Liquid Holdup of Gas-Liquid Flow in Micro-Packed Beds

Evaluation of prediction models on frictional pressure drop for condensation flow in horizontal circular tubes

Numerical modelling of twin-screw pumps based on computational fluid dynamics

Non-experimental methodology for developing pressure drop correlations for structured adsorbents with parallel channels