Abstract:Besides conventional structuring processes such as turning, milling or photo-chemical etching, laser processes are increasingly being used for surface structuring of metals. These laser processes differ fundamentally in that structuring is carried out either by material removal or by material redistribution. In this study, a new hybrid process of material ablation by means of pulsed laser radiation and material redistribution based on a remelting process by means of cw laser radiation is experimentally investigated. Besides an introduction to this new hybrid process, we give a detailed description of the equipment and methods used as well as surface structures produced on Ti6Al4V. A melt pool was generated on a prepared Ti6Al4V surface using cw laser radiation with a laser beam diameter of 520 mu m, laser power of 220 W, and a scanning velocity of 100 mm/s. In order to create surface structures, simultaneously, superimposed pulsed laser radiation with a laser beam diameter of 65 mu m, pulse duration of 60 ns, a maximum pulse energy of 0.35 mJ, and a pulse frequency of 50 kHz was used to evaporate small amounts of molten material from the melt pool. This localized evaporation of molten material is assumed to create vapor pressure that deforms the melt pool surface and therefore leads to surface structures. Our results indicate that by pulsed laser radiation capillary surface waves with a wavelength of the doubled laser beam diameter are excited on the melt pool surface. This forced excitation of capillary surface waves result in surface structures that are analyzed after solidification by means of white light interferometry. Based on this analysis we derived an oscillation frequency of v = 2.27 (+/- 0.16) kHz for the excited capillary surface wave as well as an effective kinematic viscosity of mu= 0.1328 cm(2)s(-1) for the damping of this surface oscillation during solidification. In terms of structural features, we achieved surface structures with heights of up to 100 mu m. Furthermore, structure height controllably scales in dependence on pulse energy and number of laser pulses as long as no ejection of molten material takes place. Finally, a comparison of the redistributed material volume per time shows that we achieved a volume redistribution rate of 28.37 mm(3)/min, which is significantly bigger than has been achieved with other laser texturing techniques so far and demonstrates the high potential of this new hybrid technique not only for surface structuring purposes.

Investigation of the laser ablation threshold for optimizing Laser Direct Structuring in the 3D-MID technology

Ablation Threshold Measurement and Chemical Modification of UV Nanosecond Laser Micromachining of Polycrystalline Diamond

Experimental Investigation on a New Hybrid Laser Process for Surface Structuring by Vapor Pressure on Ti6Al4V

Investigating Anisotropic Effects and Optimizing Parameters in Ultra-Short Pulsed (USP) Laser Machining of Single Crystalline Diamond (SCD)

Ablation mechanisms of nanosecond and picosecond laser scribing for metal halide perovskite module interconnection – An experimental and numerical analysis

Investigation on Hybrid Laser Ablation and Its Application in Fused Silica Damage Mitigation.

Combination of short and ultrashort pulse laser processing for productive large scale structuring of 3D plastic mould steel

Tailoring Sub-micrometer Periodic Surface Structures via Ultrashort Pulsed Direct Laser Interference Patterning

Investigation of Subsurface Damage Density and Morphology Impact on the Laser-Induced Damage Threshold of Fused Silica

Influence of working parameters on multi-shot femtosecond laser surface ablation of lithium niobate

Shape Characteristics Of Microstructures In Femtosecond Laser Multi-Pulse Ablation Of Metals

Investigation on the ablation behavior of cemented tungsten carbide by a nanosecond UV laser

Experimental probe into the femtosecond laser ablation thresholds in carbon fiber reinforced polymer and assessment of the measurement theories

A Systematic Study on the Processing Strategy in Femtosecond Laser Scribing via a Two-Temperature Model

Ablation experiment and threshold calculation of titanium alloy irradiated by ultra-fast pulse laser

Investigation of thermal and fluid dynamics behaviors of melt pool during laser direct metal deposition on inclined substrates

Theoretical basis of the diagonal scan method for determining the laser ablation threshold for femtosecond vortex pulses

Investigation of ultrashort laser excitation of aluminum and tungsten by reflectivity measurements

Two-step laser based surface treatments of laser metal deposition manufactured Ti6Al4V components

Experimental Study on Laser Microstructures Using Long Pulse

Spatio-temporal multi-scale observation of the evolution mechanism during millisecond laser ablation of SiC f /SiC