Abstract:A newly advanced heat-resistant steel SA-213 S31035 (22Cr25Ni3W3CuCoNbN), is currently the strongest commercially available austenitic heat resistant steel and has been recognized as one of the main candidate materials for A-USC plants operating at 700 °C. Up to now, the reason for which has excellent creep performance is not clear yet. In this paper, the S31035 steels were crept at 700 °C with applied stresses in the range of 140–220 MPa up to 15627 h, and during creep the microstructure evolution including the precipitation of second phases as well as their strengthening mechanisms were deeply investigated. Creep tests results show that S31035 steel has much higher creep strength than S30432 steel, with extrapolated creep rupture strength of about 118.0 MPa at 700 °C for 50,000 h. Furthermore, it has great rupture ductility with an area reduction of more than 50%. The excellent creep strength of S31035 steel was produced by the combined precipitation strengthening of nano-scaled Cu-rich phase, needle-shaped Laves phase, and secondary Z phase. The nano-scaled Cu-rich phase was very stable during long-time creep and acted as the dominant precipitation strengthening. Unlike the coarse and granular Laves phase in ferritic P92 steel (9CrW), the spindly needle-shaped Laves phase in austenitic S31035 steel could effectively impede the moving of dislocations and greatly increase the creep strength. And the coarsening of Laves phase in width was slight but in length was apparent, which was conducive to the strengthening effect. The fine secondary Z phase also showed relatively slow coarsening rate, contributed an important part of strengthening enhancement. The precipitation of detrimental σ phase is effectively suppressed through the increased content of Ni and the addition of Co. Besides, the grain-boundary sliding and grain rotation occurred during creep. Under high stresses (≥170 MPa) and short-time creep, intragranular cracks dominated the creep failure. The cracks preferred to produce inside the grains with higher Taylor factor which are hard to deform. Under relatively lower stresses (≤140 MPa), intergranular cracks dominated the creep failure and cracks mainly generate on the grain boundaries between the grains with greatly different deformations. The texture <111>//RD formed during creep, suppressing the proceeding plastic deform and improving the creep resistance. Under lower stress and long-time creep, a new texture <001>//RD occurred, which improves the creep rupture ductility of the S31035 steel.

Analysis of ECCC cross-weld creep test data on grade 92 steel

Study on Creep Behavior and Fracture Life Prediction Method of P92 Steel Based on Finite Element Analysis

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Experimental and Numerical Characterization of Low Cycle Fatigue and Creep Fatigue Behaviour of P92 Steel Welded Joint

Characterization of the Cyclic Softening and Remaining Creep Behaviour of P92 Steel Weldment

Remaining creep properties and fracture behaviour of P92 steel welded joint under prior low cycle fatigue loading

Assessment of creep rupture properties for dissimilar steels welded joints between T92 and HR3C: CREEP PROPERTIES OF T92/HR3C WELDED JOINTS

Creep Behaviors Calculated by Varying Material Constants Obtained from Different Stress Regions for a Closed-End P91 Pipe

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Creep-Fatigue Life Evaluation for Grade 91 Steels with Various Origins and Service Histories

Research of Welding Effect on Creep Damage of High Temperature Furnace Tubes

The correlation between prior fatigue damage and remaining creep properties in a high chromium steel welded joint

Assessment of Creep Properties of Haynes 282 Weld Using Deformation Mechanism-Based True Stress Model

Revealing influence of warm bending on creep performance of heat-resistant 2.25Cr-1Mo-0.25 V steel

Creep rupture study of dissimilar welded joints of P92 and 304L steels

Strengthening mechanisms and creep rupture behavior of advanced austenitic heat resistant steel SA-213 S31035 for A-USC power plants

Experimental Method for Creep Crack Growth Testing in Controlled Environments at High Temperatures

Analysis of the Creep Mechanism of Low-Alloy Steel in Terms of Plastic Deformation

Study on Creep Damage of Weldments of HK40 Furnace Tubes Based on Creep Damage Mechanics

Creep-fatigue life estimation of circumferential welds in thermal high energy piping systems

Evaluation of metallurgical risk factors in post-test, advanced 9% Cr creep strength enhanced ferritic (CSEF) steel