Abstract:High-performance engineering thermoplastics offer lightweight and excellent mechanical performance in a wide temperature range. Their composites with carbon nanotubes are expected to enhance mechanical performance, while providing thermal and electrical conductivity. These are interesting attributes that may endow additional functionalities to the nanocomposites. The present work investigates the optimal conditions to prepare polyether ether ketone (PEEK)/multi-walled carbon nanotube (MWCNT) nanocomposites, minimizing the MWCNT agglomerate size while maximizing the nanocomposite electrical conductivity. The aim is to achieve PEEK/MWCNT nanocomposites that are suitable for melt-spinning of electrically conductive multifilament's. Nanocomposites were prepared with compositions ranging from 0.5 to 7 wt.% MWCNT, showing an electrical percolation threshold between 1 and 2 wt.% MWCNT (107–102 S/cm) and a rheological percolation in the same range (1 to 2 wt.% MWCNT), confirming the formation of an MWCNT network in the nanocomposite. Considering the large drop in electrical conductivity typically observed during melt-spinning and the drawing of filaments, the composition PEEK/5 wt.% MWCNT was selected for further investigation. The effect of the melt extrusion parameters, namely screw speed, temperature, and throughput, was studied by evaluating the morphology of MWCNT agglomerates, the nanocomposite rheology, and electrical properties. It was observed that the combination of the higher values of screw speed and temperature profile leads to the smaller number of MWCNT agglomerates with smaller size, albeit at a slightly lower electrical conductivity. Generally, all processing conditions tested yielded nanocomposites with electrical conductivity in the range of 0.50–0.85 S/cm. The nanocomposite processed at higher temperature and screw speed presented the lowest value of elastic modulus, perhaps owing to higher matrix degradation and lower connectivity between the agglomerates. From all the process parameters studied, the screw speed was identified to have the higher impact on nanocomposite properties.

Broadband electrical conductivity of metal/carbon nanotubes polyamide 6 composites fabricated by reactive encapsulation

Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

Electric Conductivity and Thermorheology Properties of Polyacrylonitrile/Nylon6 Composites Filled with Carbon Black

Characterization of Single- and Multiwalled Carbon Nanotube Composites for Electromagnetic Shielding and Tunable Applications

Single-walled Carbon Nanotube–polymer Composites: Electrical, Optical and Structural Investigation

Multifunctional nanocomposites based on a polyamide 6/polyamide 12 blend and multi‐walled carbon nanotubes

Electrical Properties Of Single-Wall Carbon Nanotube-Polymer Composite Films

Microwave Properties of Carbon Nanotube/microwire/rubber Multiscale Hybrid Composites

Simultaneous use of physical and chemical dispersants for electrical conductivity enhancement in polyamide 6/carbon nanotube/conductive carbon black hybrid nanocomposites

The improved viscoelastic properties of long‐length carbon nanotubes reinforced polyamide‐6 composites

Electrical conductivity phenomena in an epoxy resin–carbon-based materials composite

The Effect of Single Walled Carbon Nanotubes on Conductivity and Thermal Properties of Glass Fiber Reinforced Composites

RESEARCH ON ELECTRICAL PROPERTIES OF PA6/CNTs COMPOSITES

Bicomponent melt spinning of polyamide 6/carbon nanotube/carbon black filaments: Investigation of effect of melt mass-flow rate on electrical conductivity

Shielding Effectiveness of CNTs/SSFs/PA6 Conductive Composites

Carbon nanotube-copper fibers produced by electrospinning: electrical conductivity measurements

Effect of structural properties in the electrical impedance spectrum of multi-walled Carbon nanotube/Graphite/Polyester ternary composites

Analytical modeling of the electrical conductivity of CNT-filled polymer nanocomposites

Effect of long-length carbon nanotubes on yield, ultimate, dynamic mechanical, and thermal properties of polyamide-6 composites prepared by twin-screw extrusion

High-Performance PEEK/MWCNT Nanocomposites: Combining Enhanced Electrical Conductivity and Nanotube Dispersion

Mechanical Properties Of Stainless Steel Fiber/Carbon Nanotube Filled Nylon Conductive Composites