Abstract:The use of carbon nanotubes (CNTs) as the reinforcing phase to prepare copper-based composite materials can improve the strength and high conductivity of copper-based conductors. In order to analyze the effect of surface oxidation modification on the structural properties of carbon nanotubes and its strengthening effect on composite materials, this article combines heterogeneous copolymerization liquid phase mixing method and spark plasma sintering molding method; prepares the carbon nanotubes/copper composite materials using carbon nanotubes under different oxidation treatment conditions as the reinforcing phase (the volume fraction of carbon nanotubes is 3%); and characterizes the microstructure, mechanical properties, and electrical and thermal conductivity of the composite material. Studies have shown that the tensile strength and hardness of composite materials first increase with the increase of CNT oxidation treatment time and then decrease with the increase of oxidation treatment time. When the oxidation treatment time is 4 h, CNTs are uniformly dispersed in the matrix while maintaining good structural integrity and load-bearing capacity, and the composite material has the highest mechanical properties. The tensile strength of the composite material made of 80‐ nm CNTs reaches 452.4 MPa, which is 1.6 times that of pure copper, and the hardness reaches 127.4HV, which is twice that of pure copper. The electrical conductivity and thermal conductivity of the composite material first increase with the increase of the oxidation treatment time of carbon nanotubes and then decrease with the increase of the oxidation treatment time. The 80 nm CNT reinforced composite material has better CNT dispersion performance and higher conductivity than that of 15 nm CNT preparation. The electrical conductivity of the composite material reaches the maximum value of 92% IACS when the CNT oxidation treatment time is 4 hours, which is 95% of the pure copper sample, and the electrical conductivity is significantly better than that of the CNT/Cu composite material and copper alloy prepared by other methods. The thermal conductivity of composite materials is lower than that of pure copper. The thermal conductivity of carbon nanotubes with an oxidation treatment time of 2 h decreases most obviously, indicating that the thermal resistance generated by the interface and agglomeration phases in the composite material affects its thermal conductivity.

Carbon nanotube-copper fibers produced by electrospinning: electrical conductivity measurements

Fabricating and Strengthening the Carbon Nanotube/copper Composite Fibers with High Strength and High Electrical Conductivity

Fabrication of Light‐Weight and Highly Conductive Copper–Carbon Nanotube Core–Shell Fibers Through Interface Design

Fabrication and Densification of High Performance Carbon Nanotube/copper Composite Fibers

A Meta‐Analysis of Conductive and Strong Carbon Nanotube Materials

Simultaneous achievement of high strength, excellent ductility, and good electrical conductivity in carbon nanotube/copper composites

Novel Synthesizing and Characterization of Copper Matrix Composites Reinforced with Carbon Nanotubes

Fabrication of high-performance carbon nanotube/copper composite fibers by interface thiol-modification

Copper/carbon nanotube composite interconnect for enhanced electromigration resistance

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Carbon Nanotube/Copper composites for via filling and thermal management

Effect of Surface Modification of Carbon Nanotubes on the Properties of High-Strength and High-Conductivity Copper Matrix Composites

Synthesis and Properties of Surface-Modified Carbon Nanotube/Copper Composites

Hardness and electrical conductivity of uncoated and silver coated carbon nanotubes reinforced copper nanocomposites

Fabrication of highly conductive carbon nanotube fibers for electrical application

Ultrastrong and Stiff Carbon Nanotube/Aluminum-Copper Nanocomposite Via Enhancing Friction Between Carbon Nanotubes

Preparation of carbon nanotube/copper/carbon fiber hierarchical composites by electrophoretic deposition for enhanced thermal conductivity and interfacial properties

Overcoming the strength-conductivity trade-off dilemma in carbon nanotube/aluminum-copper fiber by diffusion interface and chemical reaction interface

Fabrication of Cu-CNT Composite and Cu Using Laser Powder Bed Fusion Additive Manufacturing

Interfacial Bonding Improvement through Nickel Decoration on Carbon Nanotubes in Carbon Nanotubes/Cu Composite Foams Reinforced Copper Matrix Composites

Enhancement of mechanical and electrical properties of copper matrix composites by different types of carbon nanotubes