Abstract:Organic–inorganic hybrid perovskite solar cells (PSCs) are presently gaining significant attention owing to their high conversion efficiencies achieved in recent years. However, poor long-term stability against water and defects at film surfaces and grain boundaries are important factors causing performance degradation and rapid loss of the photovoltaic response. To remedy this, a pyridine derivative with long C–F chains (PFAD) is synthesized and employed as a passivator to reduce the trap states of perovskite and promote better humidity stability via antisolvent properties. The results demonstrate that the trap states of perovskite could be minimized by the presence of pyridinic nitrogen and then the formation of coordination bonds with undercoordinated Pb2+ ions. The resulting carrier recombination time is prolonged and verified via photoluminescence. The power conversion efficiency (PCE) of the PFAD-passivated perovskite solar cell increased to 20.48%, with practical elimination of hysteresis due to the high quality of the perovskite films. The significant gain generated via PFAD modification supports further applications in thin-film optoelectronic devices. Moreover, PFAD-modified devices exhibit enhanced humidity stability due to the protection of hydrophobic C–F chains from moisture; the PCE decreased about 15% after 30 days of exposure in a moisture ambient condition. Our work provides a promising strategy to further improve the performance and stability of perovskite solar cells by designing bifunctional organic molecules with passivation and hydrophobic effects.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01295.XPS spectra of perovskite and PFAD-modified perovskite; XRD patterns of perovskite films at different PFAD concentrations; J–V curves and PCE distributions of the control and PFAD-modified perovskite solar cells; and performance of perovskite solar cells at different PFAD concentrations (PDF)This article has not yet been cited by other publications.

Surface modification of perovskite film by an amino acid derivative for perovskite solar cell

Interface Passivation of Perovskite Solar Cells by Fmoc-Ala-OH Amino Acids

Interface Engineering via Amino Acid for Efficient and Stable Perovskite Solar Cells

Enhancing the Performance and Stability of Perovskite Solar Cells through the Introduction of the Multifunctional Additive 5‐Amino‐2‐Fluorobenzoic Acid

Efficient Charge Collection Promoted by Interface Passivation Using Amino Acid Toward High Performance Perovskite Solar Cells

π-Conjugated aromatic amino molecule for interfacial modification in high-performance perovskite solar cells

High efficiency and stability of perovskite solar cells from π-conjugated 5-(Fmoc-amino) valeric acid modification

Stable Surface Contact with Tailored Alkylamine Pyridine Derivatives for High‐Performance Inverted Perovskite Solar Cells

Promoting Large-Area Slot-Die-Coated Perovskite Solar Cell Performance and Reproducibility by Acid-Based Sulfono-γ-AApeptide

Passivation of perovskite surfaces using 2-hydroxyacetophenone to fabricate solar cells with over 20.7% efficiency under air environment

Stable perovskite solar cells with 25.17% efficiency enabled by improving crystallization and passivating defects synergistically

Interface modification by formamidine acetate for efficient perovskite solar cells

Enhancing Stability and Photovoltaic Performance of Perovskite Solar Cells via 5‐Ammonium Acid Additive

Natural Product Additive with Multifunctional groups Enhancing the Efficiency and Stability of Perovskite Solar Cells

Small molecule induced interfacial defect healing to construct inverted perovskite solar cells with high fill factor and stability

Interface engineering for highly efficient carbon-based all-inorganic perovskite solar cells using functionalized amino acid salts

Direct Surface Passivation of Perovskite Film by 4-Fluorophenethylammonium Iodide toward Stable and Efficient Perovskite Solar Cells

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

Surface Passivation with a Fluorocarbon-Based Pyridine Derivative for High-Crystallinity Perovskite Solar Cells with Efficiency Over 20% and Good Humidity Stability

Achieving high efficiency and stability by blocking moisture‐oxygen permeation paths on perovskite surfaces using the curing agent 4‐(2‐carboxyvinyl) benzoic acid

Self‐Induced Bi‐interfacial Modification via Fluoropyridinic Acid For High‐Performance Inverted Perovskite Solar Cells