Abstract:Organic–inorganic hybrid perovskite solar cells (PSCs) are presently gaining significant attention owing to their high conversion efficiencies achieved in recent years. However, poor long-term stability against water and defects at film surfaces and grain boundaries are important factors causing performance degradation and rapid loss of the photovoltaic response. To remedy this, a pyridine derivative with long C–F chains (PFAD) is synthesized and employed as a passivator to reduce the trap states of perovskite and promote better humidity stability via antisolvent properties. The results demonstrate that the trap states of perovskite could be minimized by the presence of pyridinic nitrogen and then the formation of coordination bonds with undercoordinated Pb2+ ions. The resulting carrier recombination time is prolonged and verified via photoluminescence. The power conversion efficiency (PCE) of the PFAD-passivated perovskite solar cell increased to 20.48%, with practical elimination of hysteresis due to the high quality of the perovskite films. The significant gain generated via PFAD modification supports further applications in thin-film optoelectronic devices. Moreover, PFAD-modified devices exhibit enhanced humidity stability due to the protection of hydrophobic C–F chains from moisture; the PCE decreased about 15% after 30 days of exposure in a moisture ambient condition. Our work provides a promising strategy to further improve the performance and stability of perovskite solar cells by designing bifunctional organic molecules with passivation and hydrophobic effects.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01295.XPS spectra of perovskite and PFAD-modified perovskite; XRD patterns of perovskite films at different PFAD concentrations; J–V curves and PCE distributions of the control and PFAD-modified perovskite solar cells; and performance of perovskite solar cells at different PFAD concentrations (PDF)This article has not yet been cited by other publications.

Achieving high efficiency and stability by blocking moisture‐oxygen permeation paths on perovskite surfaces using the curing agent 4‐(2‐carboxyvinyl) benzoic acid

Improved Crystallinity and Self-Healing Effects in Perovskite Solar Cells Via Functional Incorporation of Polyvinylpyrrolidone

Improving stability and efficiency of perovskite solar cells via a cerotic acid interfacial layer

Enhanced Efficiency and Stability of Perovskite Solar Cells by 2D Perovskite Vapor-Assisted Interface Optimization

Multifunctional Trifluoroborate Additive for Simultaneous Carrier Dynamics Governance and Defects Passivation to Boost Efficiency and Stability of Inverted Perovskite Solar Cells

Enhancing the Stability of Perovskite Solar Cells with a Multilayer Thin-Film Barrier

Passivation of perovskite surfaces using 2-hydroxyacetophenone to fabricate solar cells with over 20.7% efficiency under air environment

Improving Efficiency and Stability of Perovskite Solar Cells Enabled by A Near-Infrared-Absorbing Moisture Barrier

Reduced defects and enhanced Vbi in perovskite absorbers through synergetic passivating effect using 4-methoxyphenylacetic acid

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

Synergistic Effect of Fluorinated Passivator and Hole Transport Dopant Enables Stable Perovskite Solar Cells with an Efficiency Near 24%

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Realizing Stable Perovskite Solar Cells with Efficiency Exceeding 25.6% Through Crystallization Kinetics and Spatial Orientation Regulation

Synergistic Passivation Strategies for Enhancing Efficiency and Stability of Perovskite Solar Cells

4-biphenylcarboxylic acid as defect passivation for high-efficient perovskite solar cells

Excellent Stability of Perovskite Solar Cells by Passivation Engineering

Surface Passivation with a Fluorocarbon-Based Pyridine Derivative for High-Crystallinity Perovskite Solar Cells with Efficiency Over 20% and Good Humidity Stability

Adjustable Skeleton of Bilateral Lewis Base Passivator for CsPbI 3 Perovskite Solar Cells with PCE over 20% and Superior Stability

Grain engineering by ultrasonic substrate vibration post-treatment of wet perovskite films for annealing-free, high performance, and stable perovskite solar cells.

Ambient‐Air‐Stable Inverted Perovskite Solar Cells by Carbazole Analog Tailored Perovskite Thin Films

Using 4‐Chlorobenzoic Acid Layer Toward Stable and Low‐Cost CsPbI 2 Br Perovskite Solar Cells