Abstract:In bridge structure monitoring and evaluation, deformation data serve as a crucial basis for assessing structural conditions. Different from discrete monitoring points, spatially continuous deformation modes provide a comprehensive understanding of deformation and potential information. Terrestrial laser scanning (TLS) is a three-dimensional deformation monitoring technique that has gained wide attention in recent years, demonstrating its potential in capturing structural deformation models. In this study, a TLS-based bridge deformation mode monitoring method is proposed, and a deformation mode calculation method combining sliding windows and surface fitting is developed, which is called the SWSF method for short. On the basis of the general characteristics of bridge structures, a deformation error model is established for the SWSF method, with a detailed quantitative analysis of each error component. The analysis results show that the deformation monitoring error of the SWSF method consists of four parts, which are related to the selection of the fitting function, the density of point clouds, the noise of point clouds, and the registration accuracy of point clouds. The error caused by point cloud noise is the main error component. Under the condition that the noise level of point clouds is determined, the calculation error of the SWSF method can be significantly reduced by increasing the number of points of point clouds in the sliding window. Then, deformation testing experiments were conducted under different measurement distances, proving that the proposed SWSF method can achieve a deformation monitoring accuracy of up to 0.1 mm. Finally, the proposed deformation mode monitoring method based on TLS and SWSF was tested on a railway bridge with a span of 65 m. The test results showed that in comparison with the commonly used total station method, the proposed method does not require any preset reflective markers, thereby improving the deformation monitoring accuracy from millimeter level to submillimeter level and transforming the discrete measurement point data form into spatially continuous deformation modes. Overall, this study introduces a new method for accurate deformation monitoring of bridges, demonstrating the significant potential for its application in health monitoring and damage diagnosis of bridge structures.

What problem does this paper attempt to address?

This paper proposes a high-precision bridge deformation monitoring method based on terrestrial laser scanning (TLS) and analyzes its errors. The main goal of the study is to improve the accuracy of bridge deformation monitoring to the sub-millimeter level and obtain spatially continuous deformation patterns. A deformation pattern calculation method combining sliding window and surface fitting (SWSF) is developed in the paper to address the issues caused by point cloud noise and overfitting. In bridge structural health monitoring, deformation data is a key basis for assessing the condition of the structure. Traditional monitoring methods such as linear variable differential transducers, inclinometers, and total stations have high accuracy but are limited in application on long-span bridges. TLS, as a three-dimensional deformation monitoring technology, has attracted attention in recent years for capturing the three-dimensional deformation model of structures. However, improving the accuracy of TLS monitoring to the sub-millimeter level still faces challenges. The paper first proposes the SWSF method, which segments the point cloud using a sliding window and utilizes low-order polynomial functions for surface fitting to reduce noise and overfitting effects. Then, a deformation error model for the SWSF method is established to quantitatively analyze the error components, with point cloud noise identified as the main error source. Increasing the number of points within the sliding window can reduce the calculation error to some extent. Experimental results show that the SWSF method achieves a deformation monitoring accuracy of 0.1 millimeters at different measurement distances. When tested on a 65-meter span railway bridge, compared to the commonly used total station method, the SWSF method does not require preset reflector markers and improves the deformation monitoring accuracy from the millimeter level to the sub-millimeter level, realizing the transformation from discrete measurement point data to spatially continuous deformation patterns. In summary, this study proposes a new accurate bridge deformation monitoring method, which has significant potential for bridge structural health monitoring and damage diagnosis.

High-Precision Monitoring Method for Bridge Deformation Measurement and Error analysis Based on Terrestrial Laser Scanning

Geometrical Morphology and Deformation Measurement of Long-Span Suspension Bridge Based on Terrestrial Laser Scanning

Spatial Shape Identification of Long-Span Suspension Bridges Using 3d Laser Scanning Technology

Bridge Construction Monitoring Based on TLS and Photogrammetry

Point Cloud Registration Methods for Long-Span Bridge Spatial Deformation Monitoring Using Terrestrial Laser Scanning

Research on Bridge Spatial Deformation Monitoring Using Light Poles and Displacement-Relay Theory

A NEW APPROACH FOR SUBWAY TUNNEL DEFORMATION MONITORING: HIGH-RESOLUTION TERRESTRIAL LASER SCANNING

Structural Health Monitoring of Bridges with Personal Laser Scanning: Segment-based Analysis of systematic Point Cloud Deformations

Bridge Displacement Monitoring Method Based on Laser Projection-Sensing Technology

Efficient In-Site Laser Scanning Scheme with Adaptive Angular Resolution for Long-Span Bridge Geometry Measurement

Multi-Point Displacement Monitoring of Bridges Using A Vision-Based Approach

Full-Scale Highway Bridge Deformation Tracking via Photogrammetry and Remote Sensing

TLS for Dynamic Measurement of the Elastic Line of Bridges

Systematic Approach for Tunnel Deformation Monitoring with Terrestrial Laser Scanning

Middle Displacement Monitoring of Medium-Small Span Bridges Based on Laser Technology

A Case Study on the Application of 3D Scanning Technology in Deformation Monitoring of Slope Stabilization Structure

The Role of Terrestrial 3d Lidar Scan in Bridge Health Monitoring

Automated Change Diagnosis of Single Column Pier Bridges Based on 3D Imagery Data

Deformation monitoring of long-span railway bridges based on SBAS-InSAR technology

Terrestrial laser scanning technology for deformation monitoring and surface modeling of arch structures

Cable-stayed bridge all-round morphology identification based on 3D point cloud model