Abstract:Spray cooling, which has a fast thermal response and low flow rate consumption, is a common and effective thermal management approach for high power electronic systems. Typically, to improve the heat transfer co-efficient (HTC) for spray cooling, the target surface wettability is decreased, promoting nucleation boiling by reducing the surface energy barrier for bubble nucleation. However, the merging of bubbles and the formation of a vapor film have limitations in further increasing the critical heat flux (CHF). Hence, maximizing both the HTC and CHF of spray cooling can be mutually exclusive on the same heated surface. This paper presented a novel design for a vapor-liquid separation structure surface. It consisted of lower micropillars that serve as the vapor separation channel. On top of that, there was an upper multi-layer copper micromesh that wicks and spreads the coolant. Additionally, nano-grass attached to the micromesh to enhance capillary force and increase the nucleation sites simultaneously. Subsequently, we calculated the forward velocity and pressure drop of the droplets passing through the copper mesh to study the effects of droplet velocity and capillary force on heat transfer performance. The results show that the forward velocity of the droplets decreases rapidly as the increase of copper mesh layers and it drops to zero when passing through the third mesh. Therefore, the capillary force generated by the copper mesh is another important factor for the atomized droplets to pass through the copper mesh and reach the target surface. We have proven that all the vapor-liquid separation structure surfaces satisfy the condition Delta Pcap>Delta Ppore+Delta Plocal. Hence, the synergistic effects of the micropillar, copper micromesh, and nano-grass enable a circulation process of wicking-rewetting-vapor evacuation, which improves the onset of nucleate boiling (ONB), enhances the HTC, and increases the maximum heat flux dissipated by the system. Enhanced HTC (7.94 W/cm2/K) and maximum heat flux (817 W/cm2) were achieved at 1.50 ml/s on the vapor-liquid separation structure surfaces (#200 2-layer), representing an enhancement of 79.6% and 80.0% compared with that for the flat surface and the temperature of the heated surface at the ONB maximum decreased by approximately 30.8 degrees C.

Two-Phase Particle Image Velocimetry Visualization of Rewetting Flow on the Micropillar Interfacial Surface

Visualization of R1233zd(E) Flow Boiling in Parallel Mini-channels

Flow Boiling in Microchannels Enhanced by Parallel Microgrooves Fabricated on the Bottom Surfaces

Decrypting the mechanisms of wicking and evaporation heat transfer on micro-pillars during the pool boiling of water using high-resolution infrared thermometry

Surface roughening and hemi-wicking: Synergistic impact on flow boiling

Heat Transfer Characteristics And Flow Pattern Visualization For Flow Boiling In A Vertical Narrow Microchannel

Hybrid Surfaces with Capillary Wick and Minichannels for Enhancement of Phase-Change Immersion Cooling of Power Electronics

Coupling droplets/bubbles with a liquid film for enhancing phase-change heat transfer

Liquid Super‐Spreading Boosted High‐Performance Jet‐Flow Boiling for Enhancement of Phase‐Change Cooling

Supercapillary Architecture‐Activated Two‐Phase Boundary Layer Structures for Highly Stable and Efficient Flow Boiling Heat Transfer

Enhanced flow boiling in microchannels integrated with supercapillary pinfin fences

Experimental study on flow boiling characteristics of R134a inside high-heat-flux microchannels

Numerical Investigation on Bubble Growth and Merger in Microchannel Flow Boiling with Self-Rewetting Fluid

A heat transfer model for liquid film boiling on micro-structured surfaces

Effects of Heat Flux, Mass Flux and Two-Phase Inlet Quality on Flow Boiling in a Vertical Superhydrophilic Microchannel

Micro-pin-finned Surfaces with Fractal Treelike Hydrophilic Networks for Flow Boiling Enhancement

Experimental and computational investigation on synergistic enhancement spray cooling using micropillars and capillary-driven wicking hybrid structures

Flow Boiling in Microgaps for Thermal Management of High Heat Flux Microsystems

Experimental Study on Pool Boiling on Hydrophilic Micro/Nanotextured Surfaces with Hydrophobic Patterns

Molecular Dynamics Study of Phase Transition Heat Transfer in Water Nanofilm on Nanorough Surfaces