Abstract:A MoNx coating serves as an effective wear protection layer and is crucial for the investigation of its tribological characteristics at various temperatures. This study examined the tribological characteristics of MoNx coatings that were deposited through high-power pulsed magnetron sputtering (HiPIMS) in an Ar/N2 environment with varying N2 partial pressures. The microstructures and mechanical properties of the coatings were elucidated using scanning electron microscopy, grazing-incidence-angle X-ray diffraction, energy-dispersive spectroscopy, and nanoindentation. The dry friction performances of the coatings at different heating temperatures were studied using a ball-on-disk tribometer. The MoNx coating produced by HiPIMS was composed primarily of fcc−Mo2N and featured a fine, dense column crystal with a maximum hardness of 28.8 GPa. The MoNx coatings exhibited excellent lubrication and wear reduction properties at room temperature (RT). The dry friction performances of the MoNx coatings at elevated temperatures were expected to depend on the growth of the MoO3 tribolayer. At relatively low temperatures (300 °C and 400 °C), the MoO3 tribolayer grew slowly and was not enough to provide good lubrication, causing increases in the dry friction of the coatings. However, the δ−MoN phase formed in the MoNx coating deposited at a high N2 partial pressure could facilitate the formation of MoO3 and thus decreased the friction coefficient at 400 °C. At the relatively high heating temperature of 500 °C, however, the MoO3 tribolayer grew so rapidly that the oxide layer became thick, resulting in an increase in the wear rate. It is believed that tuning the growth rate of MoO3 via optimizing the composition and structure of the MoNx coatings might be a useful way to improve the dry friction at various elevated temperatures.

Hf–Mo–Si–B Oxidation-Resistant Coatings Produced by Magnetron Sputtering in DCMS and HIPIMS Modes

Features of Electrospark Coatings Formation on a Chromium Substrate Using Ceramic ZrSi2-MoSi2-ZrB2 and HfSi2-MoSi2-HfB2 Electrodes

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Structure and Oxidation Resistance of Mo-Y-Zr-Si-B Coatings Deposited by DCMS and HIPIMS Methods Using Mosaic Targets

Oxidation-Resistant Coatings Based on High-Entropy Alloy (MoTaNbZrHf)SiB with Increased Silicon Content, Deposited by Magnetron Sputtering

Investigation of the Al-Mo-B(CN) Coatings Deposited Using Magnetron Sputtering of Al-Mo-B4C Target Produced by Detonation Spray Coating

Oxidation Resistance of a Si-TiSi2-MoSi2-TiB2-CaSi2 Coating on a Cf/C-SiC Substrate in High-Speed High-Enthalpy Air Plasma Flows

Preparation, properties and high-temperature oxidation resistance of MoSi2-HfO2 composite coating to protect niobium using spent MoSi2-based materials

Preparation and high‐temperature oxidation resistance of multilayer MoSi 2 /MoB coating by spent MoSi 2 ‐based materials

Recycling of MoSi2-based industrial solid wastes for the fabrication and high-temperature oxidation behavior of MoSi2–ZrSi2–SiC composite coating

Effects of titanium and boron alloying with non-equimolar AlCrNbSiTi high entropy alloy nitride coatings

Frequency Effect on the Structure and Properties of Mo-Zr-Si-B Coatings Deposited by HIPIMS Using a Composite SHS Target

Oxidation Behavior of (Mo,Hf)Si2-Al2O3 Coating on Mo-Based Alloy at Elevated Temperature

Recycling MoSi2 heating elements for preparing oxidation resistant multilayered coatings

Microstructure and Composition Evolution of a Fused Slurry Silicide Coating on MoNbTaTiW Refractory High-Entropy Alloy in High-Temperature Oxidation Environment

High-temperature oxidation and ablation behavior of plasma sprayed LaB6-MoSi2-TiB2 composite coating

Fabrication of MoSi2 coatings on molybdenum and its high-temperature anti-oxidation properties

Effect of peak current on the microstructure, mechanical properties and tribological behavior of Mo x N coatings deposited by high power impulse magnetron sputtering

Dry Friction Performances of MoNx Coatings Deposited by High−Power Pulsed Magnetron Sputtering

Oxidation inhibition behaviors of HfB 2 ‐MoSi 2 ‐SiC oxygen blocking coating prepared by spark plasma sintering

Fabrication of low-density carbon-bonded carbon fiber composites with an Hf-based coating for high temperature applications