Abstract:Through a series of thermal-mechanical processing (TMP) routes with various ratios of cold rolling and subsequent high-temperature annealing, the samples with different critical strain states were prepared to explore the evolution of grain boundary character distribution (GBCD) in INCOLOY 925 during grain boundary engineering (GBE). The GBE microstructure was characterized using the electron backscatter diffraction to study the influence of TMP parameters on the evolution of GBCD and the penetration of random high angle grain boundaries. The results show that the different states of pre-strain correspond to the variational formation mechanism of grain boundary network (GBN). The strain induced boundary migration is the predominant mechanism with the rolling reduction lower than critical strain. With the slight increase of strain, the recrystallization nucleation can be initiated to generate the strain-free grains at a certain annealing temperature. Moderate strain is needed to ensure adequate growth for twin related domains (TRDs). Besides, with the increase of strain and temperature, the dominant mechanism of GBCD gradually transfers from the new twinning mechanism to the Sigma 3 regeneration mechanism. Specifically, the TMP sample with 10% rolling reduction followed by annealing at 1075 degrees C for 10min shows relatively higher grain size difference ratio and average grains numbers in the TRDs, indicating that a larger initial grain size can increase critical strain and delay the nucleation of strain-free grains during TMP treatment. The moderately higher grain size shows an opposite effect on the formation of GBN. Finally, an estimation model of critical strain, as a function of initial grain size and annealing temperature, was constructed based on the artificial neural network, and the predicted results show a high consistency with the actual microstructure evolution.

Induction of large twin related domains and the grain boundary evolution during hot plate rolling and annealing of 316H-type stainless steel

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Anomalous Evolution of Corrosion Behaviour of Warm-Rolled Type 304 Austenitic Stainless Steel

Effect of Heat Treatment Process on the Optimization of Grain Boundary Character Distribution in Heavy Gage Austenitic Stainless Steel

Grain growth behaviors during solution annealing based on the heterogeneous microstructure in hot rolled nuclear grade austenitic stainless steel

On the Critical Strain of Thermal-Mechanical Processing to Tailor Grain Boundary Character Distribution in INCOLOY 925 Alloy

Grain boundary engineering of AL6XN super-austenitic stainless steel: Distinctive effects of planar-slip dislocations and deformation twins

Evolution of grain boundary character distribution in near-surface regions of a cold-rolled nickel-based superalloy during induction heating process

Novel role of thermomechanical grain boundary engineering in the microstructure evolution of austenitic stainless steel

Consequences of Deep Rolling at Elevated Temperature on Near-Surface and Fatigue Properties of High-Manganese TWIP Steel X40MnCrAl19-2

Twins and twin-related domains in a grain boundary-engineered 304 stainless steel

On Grain Boundary Engineering for a 316L Austenitic Stainless Steel

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering

Strain-Annealing Based Grain Boundary Engineering to Evaluate its Sole Implication on Intergranular Corrosion in Extra-Low Carbon Type 304L Austenitic Stainless Steel

Formation mechanism of the eye-shaped nano-twin bundles in cold rolled 316L stainless steel

Evolution of Grain Interfaces in Annealed Duplex Stainless Steel after Parallel Cross Rolling and Direct Rolling

Microstructure evolution and recrystallization of Ti-44.5Al-3.8Nb-1Mo-0.2B alloy with different initial microstructure during hot pack rolling

Static globularization and grain morphology evolution of α and β phases during annealing of hot-rolled TC21 titanium alloy

Study on microstructure evolution and nanoindentation characteristics of 316 L austenitic stainless steel with inverse gradient grain sizes fabricated via torsion and electro-magnetic induction heating

Influence of Thermomechanical Control Process on the Evolution of Austenite Grain Size in a Low-Carbon Nb-Ti-Bearing Bainitic Steel

Evaluation of Grain Boundary Network and Improvement of Intergranular Cracking Resistance in 316L Stainless Steel after Grain Boundary Engineering