Abstract:Ni-rich layered cathode materials are important candidates for lithium-ion batteries used for high energy density applications, such as electric vehicles. However, its capacity fades during cycling, especially when a high cut off charge voltage is applied (>4.4 V). To understand the origin of this capacity fade, comprehensive diagnostic tools are applied to understand their structure, chemical and morphological properties during cycling. X-ray diffraction results show that while the LiNi0.6Mn0.2Co0.2O2 (NMC622) can mostly recover its original structure at fully discharged state, even after 0.95 Li is extracted (charged to 5.2 V), it does undergo slab sliding that leads to stacking fault (O1 type) which does not go away during cycling. In addition, transmission X-ray imaging (TXM) results indicate that cycling can induces Li content inhomogeneity within the particle. As a result, the strain builds up and is directly responsible for the cracking of primary and secondary particles. Hard X-ray absorption spectroscopy (XAS) results indicate that both Ni and Co contribute to the capacity by going through the Ni3+/Ni4+ and Co3+/Co4+ redox couples. A comparison is made between Ni-rich and the Li-rich layered materials, which is well known for the problem of oxygen release. It is found that for the Ni-rich system, the oxidization state of transition metals (bulk) are well maintained during cycling, whereas for the Li-rich system the average oxidization states keep decreasing (lower oxidation states at both fully charged and fully discharged states after cycling than the pristine sample), suggesting at least the bulk of Ni-rich material is robust against oxygen release. Soft XAS that differentiates the surface chemical information from the bulk indicates that inactive rock salt phase is formed during cycling. These results show that cycling induced strain, stacking fault and surface reconstruction are the main issues to be addressed for further improvement of this material. Acknowledgement This project was supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies through Advanced Battery Material Research (BMR) program (Battery500 consortium) under Contract No. DESC0012704. This research used resources 8-ID and 28-ID-2 of the National Synchrotron Light Source II, a U.S. Department of Energy (DOE) Office of Science User Facility operated for the DOE Office of Science by Brookhaven National Laboratory under contract no. DE-SC0012704. The authors would also like to acknowledge the use of beamline 6-2c of Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under contract no. DE-AC02-76SF00515.

Synergetic effect of high Ni ratio and low oxygen defect interface zone of single crystals on the capacity retention of lithium rich layered oxides

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Enhancing the structural stability of Ni-rich layered oxide cathodes with a preformed Zr-concentrated defective nanolayer.

Enhanced Li-ion Intercalation Kinetics and Lattice Oxygen Stability in Single-Crystalline Ni-rich Co-poor Layered Cathodes

Mitigating Evolution of Lattice Oxygen and Stabilizing Structure of Lithium-Rich Oxides by Fabricating Surface Oxygen Defects

Improving the cycling and air-storage stability of LiNi<sub>0.8</sub>Co<sub>0.1</sub>Mn<sub>0.1</sub>O<sub>2</sub> through integrated surface/interface/doping engineering

Facilitating structural stability of the Li-rich layered cathode materials by cation rearrangements and Li vacancies

Boosting cationic and anionic redox activity of Li-rich layered oxide cathodes via Li/Ni disordered regulation

High-capacity high-Ni low-Co Li-rich layered oxides via adjusting Li 2 MnO 3 content and Li/Ni mixing defects

High-capacity High-Ni Low-Co Li-rich Layered Oxides Via Adjusting Li2MnO3 Content and Li/Ni Mixing Defects

Building the Stable Oxygen Framework in High‐Ni Layered Oxide Cathode for High‐Energy‐Density Li‐Ion Batteries

Reinforcing the Stability of Cobalt-free Lithium-rich Layered Oxides via Li-poor Ni-rich Surface Transformation

Enhancing the Stability of Li-Rich Mn-Based Oxide Cathodes Through Surface High-Entropy Strategy

Achieving high structure and voltage stability in cobalt-free Li-rich layered oxide cathodes via selective dual-cation doping

Engineering oxygen vacancies in hierarchically Li-rich layered oxide porous microspheres for high-rate lithium ion battery cathode

Aluminum and polyanion-doping to improve structural and moisture stability of Ni-rich layered oxides for lithium-ion batteries

Effect of Defects on Decay of Voltage and Capacity for Li[Li0.15Ni0.2Mn0.6]O2 Cathode Material.

Reversibility of Ni-Rich Layered Cathode Material Revealed by Structural, Spectroscopic and Imaging Characterizations

Towards Rational Design of High Performance Ni-rich Layered Oxide Cathodes: the Interplay of Borate-Doping and Excess Lithium

Stabilizing lattice oxygen in slightly Li-enriched nickel oxide cathodes toward high-energy batteries

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries