Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. The used ground coffee waste (GCW) and tea leaf waste (TLW), the large wastes from the beverage process, were selected as natural reinforcement and natural pigment in the polypropylene (PP) matrix. In this work, the maleic anhydride polypropylene (MAPP) was added to the composites to develop the compatibility between fillers, fibers, and polymer matrix. The TLW/PP composites, GCW/PP composites, and GCW/TLW/PP hybrid composites were prepared in the ratio of TLW and GCW ranging from 0 to 30 wt% with the addition of MAPP at 5 wt% of fillers. The presence of GCW and TLW in the PP matrix decreased tensile properties and impact resistance but increased flexural modulus and hardness of PP at high concentrations of GCW and TLW. The increase in GCW and TLW concentration slightly reduced melting temperature but it enhanced the tensile and flexural modulus. Furthermore, it enhanced the hardness, thermal and rheological properties of the composites. The TLW/PP composites had better mechanical properties, and rheological properties than GCW/PP composites but thermal properties were quite similar. The mechanical properties of GCW/TLW/PP hybrid composites were better than those of GCW/PP composites but lower than those of TLW/PP composites. The rheological and thermal behaviour of hybrid composites were like that of TLW/PP composites. Incorporating MAPP improves the mechanical and rheological behavior of PP composites by enhancing the interaction among PP, GCW, and TLW. However, this addition does not significantly enhance the composites' thermal properties. The optimum composite was hybrid composites of GCW/TLW/PP consisting of GCW of 10 wt%, TLW of 20 wt%, and MAPP of 1.5 wt% which presented good mechanical, thermal, and rheological properties. The mechanical properties of this hybrid composites were as follows: a tensile strength of 26.35 MPa, elongation at break of 10.91%, tensile modulus of 636.69 MPa, flexural strength of 45.57 MPa, flexural modulus of 3632.86 MPa, impact resistance of 12.72 kJ/m2, and a Shore D hardness of 76.15. The overall results showed that GCW and TLW can be used as reinforcement material and natural pigment in the polymer matrix.

Biodegradable composites fabricated using recycled poly(lactic acid)-based single-use coffee cup and regenerated cellulose fiber

The biocomposites properties of compounded poly(lactic acid) with untreated and treated spent coffee grounds

Grafting Lignin with Bioderived Polyacrylates for Low-Cost, Ductile, and Fully Biobased Poly(lactic Acid) Composites

Effect of Spent Coffee Grounds on the Crystallinity and Viscoelastic Behavior of Polylactic Acid Composites

Bio-based Green Composites with High Performance from Poly(lactic Acid) and Surface-Modified Microcrystalline Cellulose

Barrier Properties and Hydrophobicity of Biodegradable Poly(lactic acid) Composites Reinforced with Recycled Chinese Spirits Distiller’s Grains

The Physical Properties and Crystallization Kinetics of Biocomposite Films Based on PLLA and Spent Coffee Grounds

Photo-oxidative resistance and adjustable degradation of poly-lactic acid (PLA) obtained by biomass addition and interfacial construction

Biodegradable green composites reinforced by the fiber recycling from disposable chopsticks

Comparing lignin and spent coffee grounds as bio‐fillers in PLA 3D‐printable filaments

Bioinspired Tannic Acid-Modified Coffee Grounds as Sustainable Fillers: Effect on the Properties of Polybutylene Adipate Terephthalate Composites

Utilization of spent coffee grounds as charring agent to prepare flame retardant poly(lactic acid) composites with improved toughness

Utilization of Spent Coffee Grounds as a Sustainable Resource for the Synthesis of Bioplastic Composites with Polylactic Acid, Starch, and Sucrose

PLA composites reinforced with rice residues or glass fiber—a review of mechanical properties, thermal properties, and biodegradation properties

Green biodegradable dielectric material made from PLA and electron beam irradiated luffa cylindrica fiber: devices for a sustainable future

Effect of Poly(propylene carbonate) on Properties of Polylactic Acid-Based Composite Films

Ecofriendly hybrid natural fiber reinforced polypropylene composites from biowastes

No Such Thing as Trash: A 3D-Printable Polymer Composite Composed of Oil-Extracted Spent Coffee Grounds and Polylactic Acid with Enhanced Impact Toughness

Preparation of degradable chemically cross-linked polylactic acid films and its application on disposable straws

A green way to simultaneously enhance the mechanical, flame retardant and anti-ultraviolet aging properties of polylactide composites by the incorporation of tannic acid derivatives

Repetitive recycling effects on mechanical characteristics of poly‐lactic acid and PLA/spent coffee grounds composite used for 3D printing filament