Abstract:Background: Mandibular first molars appear to be the most commonly tooth subjected to a root canal treatment, therefore a better understanding of the anatomy critical zones for resistance of this teeth may decrease the treatment's failure rate. So, this study was conducted to evaluate the dentin thickness of the danger zone in mesial roots of mandibular first molars using cone beam computed tomography in an Iranian population. Methods: In this cross-sectional study, 210 Cone Beam Computed Tomography acquisition of the mandibular first molars were collected from a radiology center in Qazvin. The dentin thickness of the mesial roots (mesiobuccal and mesiolingual canals) was measured from the furcation to 5 mm below. The relationship between the dentin thickness in the danger zone and parameters, like age, gender, placement side, root length, the curvature of the canal, canal type, presence of middle mesial canal, and distance between the orifices of the mesial canals was investigated. Frequency, mean and standard deviation for variables were calculated, and data analysis was done by SPSS using simple and multiple linear regression and Pearson correlation coefficient. Also, two-sample t-test was used to compare mesiobuccal and mesiolingual on two sides. The significant level was also considered at (p < 0.05). Results: The average minimum thickness of danger zone dentin was found to be 0.885 ± 0.259 mm in the mesiobuccal canal and 0.906 ± 0.206 mm in the mesiolingualcanal. Also, the minimum thickness of dentin in the mesiobuccal and mesiolingual canals in the range of 0 to 1 mm from the furcation was more than in other areas. There was no significant relationship between the minimum dentin thickness of the danger zone with gender, placement side, root length, canal type, and mesial canal entrance distance. But with increasing age, the thickness of dentin in the danger zone in the mesiolingualcanal increased significantly (p = 0.008). It was also observed that with the increase in the curvature of the canal, the thickness of the dentin in the danger zone in the mesiobuccal canal decreased (moderately curved (p = 0.008), severely curved (p = 0.046)). In addition, the thickness of the dentin in the mesiobuccal and mesiolingual canal was less in the samples with the middle mesial canal (p = 0.047, 0.044). Conclusions: Less dentin thickness in the danger zone in the mesial roots of mesiolingual mandibular first molars was seen in younger patients in mesiolingual canal, with a greater degree of canal curvature in the mesiobuccal canal and teeth with a middle mesial canal. Therefore, it is suggested that large taper instruments should be used with more precision to prevent complications.

Microcomputed tomography analysis of the radicular residual dentin thickness in mandibular second molars after virtual fiber post placement: Identification of danger zones

Micro-Computed Tomographic Analysis of Radicular Dentin Thickness in Mandibular Second Molars Across Diverse Anatomic Root Variations: Identifying Potential Danger Zones

Minimum Residual Root Dentin Thickness of Mandibular Premolars Restored with a Post: A Finite Element Analysis Study.

Effect of Access Cavity Preparation on Dentin Preservation, Biomechanical Property, and Instrumentation Efficacy: A Micro–Computed Tomographic Study

Influence of fiber post on endodontically-treated molars restored with resin-based composite：a finite element analysis

Comparison of Two Post Preparation Methods in Mandibular Second Molars with a C-shaped Root Canal Configuration.

Microcomputed tomography evaluation of contamination with endodontic obturation material remnants in teeth with different root canal anatomy after post space preparation

Finite element analysis of maxillary first molar with a 4-wall defect and 1.5-mm-high ferrule restored with fiber-reinforced composite resin posts and resin core: The number and placement of the posts

Root canal morphology and incidence of isthmus in the mesial root canal of the mandibular first molar using cone-beam computed tomography of two different scanning modes

Three-dimensional analysis of coronal root canal morphology of 136 permanent mandibular first molars by micro-computed tomography

Three-dimensional modelling and concurrent measurements of root anatomy in mandibular first molar mesial roots using micro-computed tomography

Dentin Thickness of the Danger Zone in the Mesial Roots of the Mandibular Molars: A Cone Beam Computed Tomography Analysis

Application of 3D-printed resin guides for the removal of molar fiber posts

A Comparison of Volume of Tissue Removed and Biomechanical Analysis of Different Access Cavity Designs in 2-rooted Mandibular First Molars: A Multisample 3-dimensional Finite Element Analysis

Comparison of the biomechanical effects of the post-core crown, endocrown and inlay crown after deep margin elevation and its clinical significance

Internal and external morphological analysis of fused‐rooted mandibular second molars in the Chinese population: A micro‐computed tomographic study

[Cross-sectional morphology and wall thickness of the root canal system in mandibular first premolars with C-shaped root evaluated by cone-beam CT]

Influence of Fiber Posts on the Fracture Resistance of Endodontically Treated Premolars with Different Dental Defects.

Effect of Access Cavities and Canal Enlargement on Biomechanics of Endodontically Treated Teeth: A Finite Element Analysis

Assessment of the coronal root canal morphology of permanent maxillary first molars using digital 3D-reconstruction technology based on micro-computed tomography data

Estimating the occurrence of labial bone perforation and implantation into the maxillary sinus maxillary premolars based on the morphology of maxillary premolars: A clinical study