Abstract:Phase change material (PCM) has recently been regarded as a promising thermal management means for lithium-ion (Li-ion) batteries. However, solid-liquid phase change of many current PCMs occurs in a narrow temperature range, and the cooling performance of their liquid phase is rather poor. To tackle these issues, this article presents a battery thermal management (BTM) design which injects PCM into an aluminum shell around each cell, and machines the shell inner surfaces into a row of straight rectangular fins immersed into the PCM and its outer surfaces into a plain-fin shape exposed in the air. In the mild thermal conditions, the finned shells of two adjacent cells can be embedded and passive PCM cooling is employed. Once the PCM completely melts, the shells will move apart and an airflow will be driven through the gap between them. The BTM design can also protect Li-ion batteries in a freezing environment, by taking advantage of PCM solidification when the finned shells return to their embedded configuration. A series of experiments were conducted to examine its effectiveness on two 50Ah lithium nickel cobalt manganese oxide (NCM) prismatic batteries, which were discharged at a capacity-rate of 2C and at room temperatures of T0=25∘C , 40∘C and −10∘C . It is shown that in the battery discharge at T0=25∘C , PCM in the embedded finned shells effectively reduced the average battery-surface temperature ( T ̄ ) and the maximum temperature difference ( ΔTmax ) by 21% and 36.7% , respectively, compared to bare batteries. At T0=40∘C , this BTM design successfully limited the growth of T ̄ to 9.0∘C and led to ΔTmax no more than 1.5∘C . As to the low-temperature scenario, it maintained the batteries at temperatures above T0 for 55.2% longer than those without any BTM protections. Its cooling performance was also compared with that of the conventional liquid-cooling scheme using a bottom serpentine-channel cooling plate. All these results clearly demonstrate that the BTM design in this article can compensate for the deficiencies of conventional PCM-based BTM schemes. Regardless of whether the PCM phase change is available, it has well coped with different thermal management demands of Li-ion batteries.

Thermal Characteristics of Li‐ion Battery based on Phase Change Material‐Aluminum Plate‐Fin Composite Heat Dissipation

Optimization of heat transfer and temperature control of battery thermal management system based on composite phase change materials

Parameter optimization and sensitivity analysis of a Lithium-ion battery thermal management system integrated with composite phase change material

Battery Thermal Management Using Phase Change Material-Metal Foam Composite Materials at Various Environmental Temperatures

Experimental and Simulative Investigation on Battery Thermal Management System with Structural Optimization of Composite Phase Change Material

A thermal management design using phase change material in embedded finned shells for lithium-ion batteries

Thermal performance enhancement with snowflake fins and liquid cooling in PCM-based battery thermal management system at high ambient temperature and high discharge rate

Experimental and Numerical Investigations of a Thermal Management System Using Phase-Change Materials and Forced-Air Cooling for High-Power Li-Ion Battery Packs

Thermal Performance of Pouch Lithium-ion Battery Module Cooled by Phase Change Materials

Thermal management of a LiFePO4 battery pack at high temperature environment using a composite of phase change materials and aluminum wire mesh plates

Study on thermal aspects of lithium-ion battery packs with phase change material and air cooling system

Simulation and analysis of heat dissipation performance of power battery based on phase change material enhanced heat transfer variable fin structure

Thermal management of lithium-ion batteries based on the coupling of liquid cooling and composite phase change materials

Thermal management of lithium-ion battery module using the phase change material

Study of a novel thermal management system using double-layer liquid-cooled plate-coupled PCM under high-rate discharge

Experimental and numerical investigations of lithium-ion battery thermal management using flat heat pipe and phase change material

Experiment and simulation of a LiFePO4 battery pack with a passive thermal management system using composite phase change material and graphite sheets

An Enhanced Phase Change Material Composite for Electrical Vehicle Thermal Management

Experimental investigation of the thermal performance of heat pipe assisted phase change material for battery thermal management system

Thermal Management of a Li-Ion Battery for Electric Vehicles Using PCM and Water-Cooling Board

Thermal Management System Using Phase Change Material for Lithium-ion Battery