Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Structural and Phase Transformations and Crystallographic Texture in Industrial Ti–6Al–4V Alloy with Globular Morphology of α-Phase Grains: Plate's Transverse Section along Rolling Direction

Structural and Phase Transformations and Crystallographic Texture in Industrial Ti–6Al–4V Alloy with Globular Morphology of α-Phase Grains: Plate's Transverse Section Perpendicular to Rolling Direction

Mechanism of Crystallographic Orientation and Texture Evolution of Ti60 Alloy during Plane Strain Compression

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

The Role of Deformation and Microstructure Evolution on Texture Formation of a TA15 Alloy Subjected to Plane Strain Compression

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Deformation and Phase Transformation of Disordered α Phase in the (α + γ) Two-Phase Region of a High-Nb TiAl Alloy

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

In-situ synchrotron high energy X-ray diffraction study on the deformation mechanisms of D0 19 -α 2 phase during high-temperature compression in a TiAl alloy

Microstructural Development, Deformation Behavior, and Texture Evolution Investigation during Hot Compression of a Dynamically Recrystallized Ti-5Cu Alloy in the Dual (α + β) Phase Region

Transverse texture weakening and anisotropy improvement of Ti-6Al-4V alloy sheet via asymmetric rolling and static recrystallization annealing

Microstructure and Texture Evolution of Ti65 Alloy during Thermomechanical Processing

Texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr dual-phase alloy during cold rolling based on multiscale crystal plasticity finite element model

Effect of Hot Rolling Temperature on Microstructure Evolution, Deformation Texture and Nanoindentation Properties of an Intermetallic Ti-43Al-9V-0.2Y Alloy

Effect of Texture on the Ductile–Brittle Transition Range and Fracture Mechanisms of the Ultrafine-Grained Two-Phase Ti-6Al-4V Titanium Alloy

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments

Microstructures and mechanical properties of Ti-55511 alloy subjected to rolling in the α+β dual-phase region

Microstructure and Texture Characterstics of a Near-Alpha Titanium Alloy Tube