Abstract:Multi-layer fabrics are commonly used in ballistics shields with a lower bulletproof class to protect against pistol and revolver bullets. In order to additionally limit the dynamic deflection of the samples, layers reinforced with additional materials, including non-Newtonian fluids compacted by shear, are additionally used. Performing a wide range of tests in each case can be very problematic; therefore, there are many calculation methods that allow, with better or worse results, mapping of the behavior of the material in the case of impact loads. The search for simplified methods is very important in order to simplify the complexity of numerical fabric models while maintaining the accuracy of the results obtained. In this article, multi-layer composites were tested. Two samples were included in the elements subjected to shelling. In the first sample, the outer layers consisted of aramid fabrics in a laminate with a thermoplastic polymer matrix. The middle layer contained a non-Newtonian shear-thickening fluid enclosed in hexagonal (honeycomb) cells. The fluid was produced using polypropylene glycol and colloidal silica powder with a diameter of 14 µm in the proportions of 60/40. The backing plate was made using a 12-layer composite made of Twaron® para-aramid fabrics with a DCPD matrix-not yet used in a wide range of ballistics. Then, numerical simulations were carried out in the Abaqus/Explicit dynamic analysis. The Johnson-Cook constitutive strength model was used to describe the behavior of elastic-plastic materials constituting the elements of the projectiles. For the non-Newtonian fluid, a Up-Us EOS was used. The inner layers of the fabric were treated as an orthotropic material. Complete homogenization of the sample layers was carried out, thanks to which each layer was treated as a homogeneous continuum. As a parameter of fracture mechanics for shield components, the strain criterion was used with the smooth particles hydrodynamics method (SPH). Then, the results of simulations were compared with the results of the ballistic test for both samples placed next to each other, which resulted in the formation of a multi-layer composite in one ballistic test subjected to impact loads during firing with a 9 × 19 mm Parabellum FMJ projectile with an initial velocity of 370 ± 10 m/s. The results of numerical tests are very similar to the ballistic tests, which indicates the correct mapping of the process and the correct conduct of layer homogenization. The applied proportions of the components in the non-Newtonian fluid allowed a reduction in the deflection compared to previous studies. Additionally, the proposal to use a DCPD matrix allowed to obtain a much lower deflection value compared to other materials, which is a novelty in the field of production of ballistic shields.

Experimental Method For Studying The Interaction Processes Of High-Velocity Impactors With Multilayer Transparent Armor

Numerical Study on the Perforation of Steel Plates by Multiple Projectiles

Strain-rate-dependent Cohesive Zone Modelling of Charge Damage Behavior when a Projectile Penetrates Multilayered Targets

Soft Impact Response of Laminated Glass Plates

Deformation and Damage Mechanisms of Laminated Glass Windows Subjected to High Velocity Soft Impact

Numerical simulation of high-speed penetration-perforation dynamics in layered armor shields

Assessment of Multilayered Plates with Hyperelastic Coatings Subjected to Dynamic Loadings by Impact at Low Velocities

Experimental and Numerical Analysis of the Damage Mechanism of an Aramid Fabric Panel Engaged in a Medium-Velocity Impact

Numerical simulation of the disk fragment impacting resistance of plate target

Experimental and Numerical Analysis of a Car Body Shield Loaded with a Ballistic Impact

Experimental and Numerical Investigation on the Perforation Resistance of Double-Layered Metal Shield under High-Velocity Impact of Armor-Piercing Projectiles

An investigation of the ballistic impact behavior of multi-layered armor structure

Multi-Layer Fabric Composites Combined with Non-Newtonian Shear Thickening in Ballistic Protection-Hybrid Numerical Methods and Ballistic Tests

Experiment and Numerical Simulation of Damage Progression in Transparent Sandwich Structure under Impact Load

Experimental Investigation on the Damage Characteristics for Light Armored Vehicle by Large Caliber Rifle Projectile

Experimental investigation on the ballistic performance of double-layered plates subjected to impact by projectile of high strength

Predictive Models and Experiments for High-Velocity and High-Temperature Impacts in Inconel-alloy Panels

Numerical investigation on dynamic damage behavior of a novel N-shaped perforated armor plate under ballistic impact

The Effect of Material Layering Order on the Ballistic Performances of Targets Against the Impact of Ogival-Nosed Projectiles

Ballistic performance of Polycarbonate and Polymethyl methacrylate under normal and inclined dynamic impacts

Analysis of Ballistic Impact of 7.62 mm FMJ M80 Rifle Projectile into Twaron/UHMWPE Composite Armor