Abstract:Wastewater treatment based on activated sludge processes faces a major challenge due to an increased number of people contributing to wastewater and changes in wastewater characteristics in regions with seasonal winter tourism. The combination of significant increases in carbon (COD) and nitrogen (N) loads by a factor of four to five within a short periode of time and low wastewater temperatures (<12 °C), represents a bottleneck in meeting essential effluent requirements. According to literature research, however, little attention has been paid to these special framework conditions for wastewater treatment. Based on this fact, a model-based simulation study of the wastewater treatment plant (WWTP) in Montafon (Austria) evaluates operational optimization approaches for the above-mentioned framework conditions and is intended to provide new insights for nitrification-optimized and energy-optimized wastewater treatment. The WWTP Montafon is designed for a COD load of 6250 kg d −1 , a daily dry weather water discharge of 12,700 m 3 d −1 and is a typical plant in a winter tourism region. The 5 studied smart operation approaches shown are a combination of two different aeration control strategies based on a time-controlled (i) or ammonia-based feedback aeration control (ABAC) (ii) for intermittent nitrification-denitrification and sludge removal control strategies based on a constant sludge concentration to 3 g L −1 (iii), a constant sludge retention time (SRT) to 20 days (iv) and a constant sludge retention time to 20 days combined with a higher level sludge concentration control to max. 3 g L −1 (v). The simulation results show that a combination of a time-controlled aeration strategy and controlling the sludge concentration to a constant 3 g L −1 is not recommended in order to comply with the emission limits. Under the mentioned influent conditions, ABAC control alone does not inevitably lead to a nitrification-optimized process and reduction in energy consumption. Sufficient nitrifying bacteria in the activated sludge are the key to a nitrification optimized process and reduction of energy consumption for aeration. Hence, a combination of an intermittent aeration control based on ammonium measurement and a constant sludge retention time to 20 days is preferable for nitrification capacity and is the most energy-efficient control strategy to obtain required COD and N effluent quality. An average energy consumption of 57–63 Wh PE 120 −1 d −1 for the aeration is to be expected for combinations of (i,iv), (ii, iii) (ii,iv) and (ii,v) which is low in relation to the influent challenges and to plants with higher wastewater temperatures (>12 °C) between 27 Wh PE 120 −1 d −1 and 121 Wh PE 120 −1 d −1 according to literature. The approach with a time-controlled intermittent aeration and a SRT to constant 20 days was implemented at the WWTP Montafon and confirms the results of the associated simulation. According to this simulation study, a 35 % increase in nitrification capacity in existing WWTPs designed as activated sludge processes can be achieved through optimized operating conditions without additional high investments.

Optimisation of the energy consumption in activated sludge treatment plants using simulation model

Comparative assessment of different scenarios for upgrading activated sludge wastewater treatment plants in developing countries

Determine the most effective process control parameters on activated sludge based on particle swarm optimisation algorithm (Case Study: South wastewater treatment plant of Tehran)

Model-based dynamic simulation study to boost the WWTP performance in winter tourism regions

Assessment and optimization of wastewater treatment plant in terms of effluent quality, energy footprint, and greenhouse gas emissions: An integrated modeling approach

Simulation and optimization of ammonia removal at low temperature for a double channel oxidation ditch based on fully coupled activated sludge model (FCASM): a full-scale study.

A Practical Methodology for Forecasting the Impact of Changes in Influent Loads and Discharge Consents on Average Energy Consumption and Sludge Production by Activated Sludge Wastewater Treatment

A simulation-based integrated approach to optimize the biological nutrient removal process in a full-scale wastewater treatment plant

Nutrient Removal from Industrial Wastewater Systems Using Controlled Activated Sludge Treatment

Investigating the effect of changing the decay coefficient in an activated sludge model

Mathematical Simulation of Feedforward Control for Nutrient Removal in Anaerobic-Anoxic-oxic Processes.

Modelling to Lower Energy Consumption in a Large WWTP in China While Optimising Nitrogen Removal

Reducing aeration energy consumption in a large-scale membrane bioreactor: Process simulation and engineering application

A combined support vector regression with a firefly algorithm for prediction of energy consumption in wastewater treatment plants

An online method for estimation of degradable substrate and biomass in an aerated activated sludge process

Modeling and optimizing of an actual municipal sewage plant: A comparison of diverse multi-objective optimization methods

Improvement of effluent quality and operational cost reduction of a wastewater treatment plant using intelligent computational hybrid control schemes

Decentralized proportional-integral control with carbon addition for wastewater treatment plant

Investigation, biokinetic calculation, and modelling of a real combined industrial wastewater biological treatment process by activated sludge models

Parameter Optimisation of Aerobic Granular Sludge at High Temperature Using Response Surface Methodology

Optimized wastewater management utilizing multivariate statistical analysis: a case study of the Mascara wastewater treatment plant, Algeria