Abstract:Background: Polyethylene (PE) wear and material degradation have been reported as complications in reverse total shoulder replacements (rTSAs). In this regard, scapular notching is associated with more clinical complications. Therefore, the purposes of the study were to quantify the linear and volumetric wear, as a measure for the amount of removed material, and to qualitatively assess the PE damage modes to describe the material degradation in retrieved rTSA humeral PE inlays that contribute to failure of shoulder replacements. Furthermore, this study aimed to evaluate the effect of scapular notching on PE wear and rim damage of the humeral components. Methods: The total study population of 39 humeral inlays contains 2 cohorts that were used for the damage mode analysis and for the wear analysis, respectively. The extent and presence of wear damage modes in 5 defined zones were assessed by a grading system for all PE joint replacements. For quantitative wear analysis the most frequent design (n = 17) was chosen. Using a coordinate-measuring machine and postprocessing software, volumetric wear measurements for the retrieved humeral PE inlays were undertaken. Furthermore, prerevision radiographs were analyzed for scapular notching. Finally, retrieval findings were correlated with clinical and radiographic data to consider the effect of notching and to identify risk of failures for these prostheses. Results: Damage on the rim of the humeral PE inlays was more frequent and severe than on the intended articulation surface. Irrespective of the damage mode, the inferior rim zone sustained the greatest amount of wear damage followed by the posterior zone. Burnishing, scratching, pitting, and embedded particles are most likely to occur in the articular surface area, whereas surface deformation, abrasion, delamination and gross material degradation are predominantly present in the inferior and posterior rim zones. The retrieved inlays exhibited a mean volumetric wear rate of 296.9 mm³/yr ± 87.0 mm³/yr. However, if the notched and non-notched components were compared, a significant higher volumetric wear rate (296.5 ± 106.1 mm³/yr) was found for the notched components compared to the non-notched group (65.7 ± 7.4 mm³/yr). Generally, there was a significantly greater incidence of damage and greater amount of wear if scapular notching occurred. Conclusion: The notched components showed a 5-fold increase in PE wear rate. Therefore, scapular notching has a strong effect on PE damage and wear. If scapular notching can be clinically avoided, the PE wear performance is in a similar magnitude as found for hip and knee replacements.

Methods to assess in vitro wear of articular cartilage

Comparison of wear on articular cartilage by titanium alloy, ultra-high-molecular-weight polyethylene, and carbon fibre reinforced polyether-ether-ketone: A pilot study

AFM-Based Method for Measurement of Normal and Osteoarthritic Human Articular Cartilage Surface Roughness

The Quantification of Physiologically Relevant Cross-Shear Wear Phenomena on Orthopaedic Bearing Materials Using the MAX-Shear Wear Testing System

Total Hip Wear Assessment: A Comparison Between Computational and In Vitro Wear Assessment Techniques Using ISO 14242 Loading and Kinematics

Numerical investigation on the wear characteristics of hip implant under static loading

The performance of resurfacing implants for focal cartilage defects depends on the degenerative condition of the opposing cartilage

Friction and wear properties of polymer, metal, and ceramic prosthetic joint materials evaluated on a multichannel screening device

Measurement of polyethylene wear and its clinical significance in total hip arthroplasty

A rolling-gliding wear simulator for the investigation of tribological material pairings for application in total knee arthroplasty

Effects of focal metallic implants on opposing cartilage - an in-vitro study with an abrasion test machine

Ceramic–Titanium Alloy Artificial Hip Joint Wear Simulation and Experimental Study

Hemiarthroplasties: the choice of prosthetic material causes different levels of damage in the articular cartilage

Mechanical Testing of Hydrogels in Cartilage Tissue Engineering: Beyond the Compressive Modulus

Evaluation of apparent fracture toughness of articular cartilage and hydrogels

A comparison of three different methods for the quantification of the in vitro wear of dental materials

Cross-shear implementation in sliding-distance-coupled finite element analysis of wear in metal-on-polyethylene total joint arthroplasty: intervertebral total disc replacement as an illustrative application

Wear and damage in retrieved humeral inlays of reverse total shoulder arthroplasty-where, how much, and why?

A New Method of In Vitro Wear Assessment of the UHMWPE Tibial Insert in Total Knee Replacement

Development of a hybrid computational/experimental framework for evaluation of damage mechanisms of a linked semiconstrained total elbow system

Functional performance of a bi-layered chitosan-nano-hydroxyapatite osteochondral scaffold: a pre-clinical in vitro tribological study