Abstract:The latent heat of phase change allows to increase the energy density compared to sensible storage. In the building sector, it is possible to replace hot water tanks that are bulky due to their cylindrical shape, by smaller storage volume and cuboid geometry. The idea of the new concept is thus to propose a hybrid and modular storage component with several cavities containing each the phase change material (PCM) delimited by two flat heat exchangers (solar + DHW) connected by slotted fins. It was developed for a solar domestic hot water system in a single-family house. The first step was to precisely characterize the behavior of the two selected PCMs during melting and solidification, without and with supercooling (respectively RT58 and PEG6000). The next step concerns the modeling of the storage cavity and then the optimization of the new full-size concept for solar domestic hot water systems. A prototype was experimentally tested for the two PCMs under real operating conditions with a reduced sequence of six days allowing the annual performance to be calculated. The experimental results confirm the known limit of PCM concerning its low thermal conductivity, which can penalize the power extracted from the storage during continuous withdrawals. The spacing of the fins thus plays a major role in heat transfer. The evaluation of the annual performances carried out on the prototype shows that the solar fraction is quite satisfactory, between 40 and 90 % depending on the climate in France. The distribution of average temperatures observed within the PCM is directly correlated with the melting ranges. The RT58 is thus penalized compared to the PEG6000 because the start of the melting takes place at a much lower level (30 °C against 52 °C), which can lead to more frequent use of back-up. Regarding heat storage, the much lower density of the RT58 explains the difference in energy stored in the prototype (+34 % for the PEG6000 between 20 and 80 °C) knowing that the latent heat and the specific heat are of the same order of magnitude in both cases. Finally, the higher thermal conductivity of PEG6000 favors the heat rate exchanged during the storage charging and discharging phases.

Optimization of the mass ratio and melting temperature of PCMs integrated in Salt Gradient Solar Ponds

Investigation of the PCM layer thickness and heat extraction on the thermal efficiency of salt gradient solar ponds

Experimental Investigation of the Comprehensive Heat Transfer Performance of PCMs Filled with CMF in a Heat Storage Device

Optimization of Thermal Performance in Thermocline Tank Thermal Energy Storage System with the Multilayered PCM(s) for CSP Tower Plants

Enhanced performance and stability of a solar pond using an external heat exchanger filled with nano-phase change material

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Improvement of the efficiency of solar thermal energy storage systems by cascading a PCM unit with a water tank

Structure Optimization of a Phase Change Material Integrated Solar Air Collector/storage Unit Based Upon Phase Change Analysis

A Review of Numerical Modelling of High-Temperature Phase Change Material Composites for Solar Thermal Energy Storage

Enhancement of PCMs performance using nano-particles in horizontal triple-series shell-and-tube heat exchangers: A numerical study

Performance comparison of two PCM candidates for new concept of compact thermal storage in solar DHW systems

Experimental and Numerical Investigation of a Solar Collector/storage System with Composite Phase Change Materials

Design improvement of a laboratory prototype for efficiency evaluation of solar thermal water heating system using phase change material (PCMs)

The Thermal Stratification Evaluation of Phase-Change Materials in a Heat Storage Tank: Computational Fluid Dynamics and Experimental Study

Enhancing the summer efficiency of solar ponds through integration of paraffin wax and carbon soot nanoparticles

Numerical Comparison Between Single PCM and Multi-Stage PCM Based High Temperature Thermal Energy Storage for CSP Tower Plants

Optimization of the packed-bed thermal energy storage with cascaded PCM capsules under the constraint of outlet threshold temperature

Thermo-economic Evaluation of PCM Layer Thickness Change on the Performance of the Hybrid Heat Storage Tank for Concentrating Solar Power Plants

Numerical Investigation of the Melting Temperature Effect on the Performance of Thermocline Thermal Energy Storage Tank for CSP

Preparation and characterization of shape-stable phase change particles: A new option for high-temperature thermal energy storage

Enhancing the performance of paraffin's phase change material through a hybrid scheme utilizing sand core matrix