Abstract:In this study, we demonstrated a Monte Carlo simulation to model a finger structure and to calculate the intensity of photons passing through tissues, in order to determine optimal angular separation between a photodetector (PD) and a light-emitting diode (LED), to detect SpO2. Furthermore, our model was used to suggest a mirror-coated ring-type pulse oximeter to improve the sensitivity by up to 80% and improve power consumption by up to 65% compared to the mirror-uncoated structure. A ring-type pulse oximeter (RPO) is widely used to detect photoplethysmography (PPG) signals for SpO2 measurement during sleep and health-status monitoring. Device sensitivity and the power consumption of an RPO, which are key performance indicators, vary greatly with the geometrical arrangement of PD and LED within the inner surface of an RPO. We propose a reflection-boosted design of an RPO to achieve both high sensitivity and low power consumption, and determine an optimal configuration of a PD and LED by performing a 3D Monte Carlo simulation and confirming its agreement with experimental measurement. In order to confirm the reflection-boosted performance in terms of signal-to-noise ratio, R ratio, and perfusion index (PI), RPOs were fabricated with and without a highly reflective coating, and then used for SpO2 measurement from eight participants. Our simulation allows the numerical calculation of the intensity of photon passing and scattering through finger tissues. The reflection-boosted RPO enables reliable measurement with high sensitivity, resulting in less power consumption for the LED and longer device usage than conventional RPOs without any reflective coating, in order to maintain the same level of SNR and PI. Compared to the non-reflective reference RPO, the reflection-boosted RPO design greatly enhanced both detected light intensity (67% in dc and 322% in ac signals at a wavelength λ1 = 660 nm, and also 81% and 375% at λ2 = 940 nm, respectively) and PI (23.3% at λ1 and 25.5% at λ2). Thus, the reflection-boosted design not only enhanced measurement reliability but also significantly improved power consumption, i.e., by requiring only 36% and 30% power to drive the LED sources with λ1 and λ2, respectively, to produce the device performance of a non-reflective RPO reference. It is expected that our proposed RPO provides long-term monitoring capability with low power consumption and an enhanced PI for SpO2 measurement.

A New Reflectance Pulse Oximeter Housing to Reduce Contact Pressure Effects

Optical Fibre-Based Pulse Oximetry Sensor with Contact Force Detection

Reflection-Boosted Wearable Ring-Type Pulse Oximeters for SpO2 Measurement with High Sensitivity and Low Power Consumption

Recent Progress in Flexible and Wearable All Organic Photoplethysmography Sensors for SpO2 Monitoring

Design and Development of a Low Cost Pulse Oximeter

Effect of Skin Pigmentation and Finger Choice on Accuracy of Oxygen Saturation Measurement in an IoT-Based Pulse Oximeter

Dual-ratio approach to pulse oximetry and the effect of skin tone

Accuracy enhancement in reflective pulse oximetry by considering wavelength-dependent pathlengths

Exploring the impact of pulse oximeter selection within the COVID-19 home-use pulse oximetry pathways

Investigation of Photoplethysmography Behind the Ear for Pulse Oximetry in Hypoxic Conditions with a Novel Device (SPYDR)

Tissue mimicking materials and finger phantom design for pulse oximetry

The high price of equity in pulse oximetry: A cost evaluation and need for interim solutions

A Study on Impacts of Ambient Lights and Skin Tone for Contactless Blood Oxygen Measurement using Visible Spectrum Facial Videosaper

Pulse Oximeter Performance, Racial Inequity, and the Work Ahead

Wrist-Sensor Pulse Oximeter Enables Prolonged Patient Monitoring in Chronic Lung Diseases

Interface Sensors with Skin Piezo-Thermic Transduction Enable Motion Artifact Removal for Wearable Physiological Monitoring

Wearable Multisensor Ring-Shaped Probe for Assessing Stress and Blood Oxygenation: Design and Preliminary Measurements

Effect of probe contact pressure on the photoplethysmographic assessment of conduit artery stiffness

3D Printing Silicone Elastomer for Patient‐Specific Wearable Pulse Oximeter

Wrist02 -- Reliable Peripheral Oxygen Saturation Readings from Wrist-Worn Pulse Oximeters