Abstract:With the increasing severity in the service environment of secondary refining furnaces, traditional refractories cannot meet the high requirements. MgO-based fired refractories are subject to the thermal shock effect and slag penetration which are detrimental to their performance. In this study, low-carbon MgO-based refractories are reinforced by an in-situ MgAl2O4(MA)-TiO2 dense layer with the addition of low-cost self-prepared titanium carbonitride [Ti(C, N)]. The influence of the addition of as-prepared Ti(C, N) on the properties of low-carbon MgO-based refractories was investigated. The reinforced refractories had no cracks after 190 thermal shock cycles, demonstrating the highest hot modulus of rupture (HMOR) with excellent thermal shock resistance (TSR). After 2.5 h of rotary immersion in a steel slag, the corrosion depth of the composites was only 26.3% of that of commercial MgO-CaO refractories. Based on the thermodynamic analysis, the Ti(C, N) reinforcement mechanism for the low-carbon MgO-based refractories was studied. A MA-TiO2 dense layer formed during the oxidation process of the composites which enhanced the oxidation resistance. The volume expansion caused by the partial oxidation of Ti(C, N) prevents the penetration of the molten slag to refractories and Ti(C, N) powders forming a protective layer to further effectively protect the composites from slag corrosion owing to its high surface area. In addition, 3CaO·2TiO2 formed by the reaction between the steel slag and Ti(C, N) further increased the slag corrosion resistance (SCR) of the composites. This research offers a new idea for the material selection for secondary refining furnaces to achieve a green and effective steel-making production route and enriches the understanding of the phase behaviour in the Mg-Al-Ti-C-O-N system under high temperatures.

Evolution of iron-based raw materials and their effect on the properties of MgO-Al-C slide plate materials

Mechanical properties and microstructure evolution of MgO–Al–C slide plate refractories in presence of Al powder-modified magnesia aggregates

Fabrication of Y2O3-doped MgO Refractory Raw Materials Based on Magnesium Hydroxide from Salt-Lake Brine

Role of nano-Al2O3 particles in improving the properties of MgO–C slide plate materials

Effect of Al2O3 on the Molten Slag Microstructure Information by Molecular Dynamics Simulation and Experimental Analysis

New Insights on Consolidation Behavior of Fe2O3 in the Fe3O4-CaO-MgO-SiO2 System for Fluxed Pellet Production: Phase Transformations and Morphology Evolution

Effect of stainless steel fibers on properties of MgO–C refractories

Preparation and properties of MgAl 2O 4-CaAl 12O 19 high temperature composite

Effect of raw material composition on microstructures and properties of microporous MgO–Mg(Al, Fe) 2 O 4 refractory aggregates

Properties and microstructure evolution of unfired Al–Si incorporated Al2O3–C slide plate materials with trace nano-Al2O3 particles

The microstructure evolution and performance enhancement of MgO-C refractories by the addition of MA90 spinel micro-powder

Microstructure evolution, mechanical characteristics and erosion behavior of Cr2O3–Al2O3–MgO–ZrO2 refractories in molten reduction slag

Microstructures and strength of microporous MgO-Mg(Al, Fe)2O4 refractory aggregates

Improved Middle-Temperature Strength of Unfired Slide Gate Plate for Continuous Casting of Steel

Effect of C/MgO nanocomposite powders on the properties of low-carbon MgO–C refractories

Development of an Ultra-Low Carbon MgO Refractory Doped with α-Al2O3 Nanoparticles for the Steelmaking Industry: A Microstructural and Thermo-Mechanical Study

Improved properties of in-situ MgAl2O4-TiO2 dense layer reinforced low-carbon MgO-based refractories

Mechanical Behavior and Thermal Shock Resistance of MgO-C Refractories: Influence of Graphite Content

Preparation and Properties of MgAl<sub>2</sub>O<sub>4</sub>-CaAl<sub>12</sub>O<sub>19</sub> High Temperature Composite

Effect of Al2O3 on Sintering and Thermal Shock Resistance of MgO Ceramic

Microstructures and Strengths of Microporous MgO‐Al2O3 Refractory Aggregates Using Two Types of Magnesite