Abstract:Perovskite solar cells based on the inorganic/organic hybrid perovskite have attracted increasing attention over the past 3 years. Many studies have been done in this area. Controling the morphology of the perovskite film is an effective way to improve the photoelectric conversion efficiency of the devices. In our reserch, we studied the influence of structure and morphology of perovskite films on the performance of the organic-inorganic hybrid perovskite solar cells which prepared by a sequential deposition method. Mesoporous TiO2 scaffold were introduced as electron collecting layer. Lead iodide (PbI2) was then spin cast on the TiO2 scaffold. The PbI2 subsequently transformed into the perovskite (CH3NH3PbI3) by dipping the TiO2/PbI2 film into a solution of CH3NH3I. We studied the difference between the PbI2 film with or without drying under room temperature after spin-coating. Through drying under room temperature, larger pores formed in the PbI2 film. While without drying under room temperature, smaller and shallower pores formed in the PbI2 film. The results show that larger pores in PbI2 film leads to more complete transformation of PbI2 to CH3NH3PbI3 and larger CH3NH3PbI3 particles. CH3NH3PbI3 films were prepared with three different processes: (a) direct dipping the PbI2 film with smaller pores into the CH3NH3I solution; (b) direct dipping the PbI2 with larger pores into the CH3NH3I solution; (c) dipping the PbI2 with larger pores into the CH3NH3I solution after pre-wetting. The resulting CH3NH3PbI3 films were studied with SEM, UV-vis absorption spectrum and XRD. The particles size of the CH3NH3PbI3 are 150, 250 and 350 rim for process (a), (b) and (c) respectively. CH3NH3PbI3 films fabricated through process (a) show insufficient absorption due to the insufficient transformation of the PbI2. The pre-wetting procedure leads to slower reaction result in larger CH3NH3PbI3 particle size. Devices with proper size of CH3NH3PbI3 particles show the highest photoelectric conversion efficiency. An efficiency of 13.5% was achieved with a J(sc) of 17.8 mA/cm(2), a V-oc of 1.05 V and a FF of 72.5%.

Use of Anodic TiO2 Nanotube Layers as Mesoporous Scaffolds for Fabricating CH3NH3PbI3 Perovskite-based Solid State Solar Cells

Metal Organic Framework Doped Spiro-OMeTAD with Increased Conductivity for Improving Perovskite Solar Cell Performance

All solid-state solar cells based on CH3NH3PbI3-sensitized TiO2 nanotube arrays

A facile spray-assisted fabrication of homogenous flat CH3NH3PbI3 films for high performance mesostructure perovskite solar cells

Liquid Phase Deposition of Tio2 Nanolayer Affords Ch3nh3pbi3/Nanocarbon Solar Cells with High Open-Circuit Voltage

Applying Neoteric MgTiO3-coated TiO2 Nanoparticulate Films As Scaffold Layers in Perovskite Solar Cells Based on Carbon Counter Electrode for Retarding Charge Recombination

Enhanced photovoltaic performance of perovskite CH₃NH₃PbI₃ solar cells with freestanding TiO₂ nanotube array films.

TiO2/SnO2 Nanocomposites As Electron Transporting Layer for Efficiency Enhancement in Planar CH3NH3PbI3-Based Perovskite Solar Cells

Full Printable Perovskite Solar Cells Based on Mesoscopic Tio2/Al2o3/Nio (carbon Nanotubes) Architecture

The Properties of the CH3NH3PbI3/TiO2 Composite Layer Prepared from PbO-TiO2 Mesoporous Layer under Air Ambience

Radio Frequency Magnetron Sputtering Deposition of TiO2 Thin Films and Their Perovskite Solar Cell Applications

Lead Methylammonium Triiodide Perovskite-Based Solar Cells: an Interfacial Charge-Transfer Investigation.

Laminated carbon nanotube networks for metal electrode-free efficient perovskite solar cells.

Direct Conversion of CH3NH3PbI3 from Electrodeposited PbO for Highly Efficient Planar Perovskite Solar Cells

Mesoporous Sno2 Nanoparticle Films As Electron-Transporting Material in Perovskite Solar Cells

Mesoporous PbI2 Scaffold for High-Performance Planar Heterojunction Perovskite Solar Cells Via Sequential Deposition Process

A Novel Conductive Mesoporous Layer with a Dynamic Two-Step Deposition Strategy Boosts Efficiency of Perovskite Solar Cells to 20%

Enhanced photovoltaic performance of perovskite CH 3 NH 3 PbI 3 solar cells with freestanding TiO 2 nanotube array films

Harnessing SWCNT absorber based efficient CH3NH3PbI3 perovskite solar cells

Influence of Structure and Morphology of Perovskite Films on the Performance of Perovskite Solar Cells

Microstructure Modulation Of The Ch3nh3pbi3 Layer In Perovskite Solar Cells By 2-Propanol Pre-Wetting And Annealing In A Spray-Assisted Solution Process