Abstract:Abstract The theoretical analysis of the acid-fracturing process for turbulent-flow conditions has been process for turbulent-flow conditions has been reconsidered taking fluid losses into account. For a simple fracture model and an idealized acidizing process, the acid concentration in the fracture process, the acid concentration in the fracture during acid injection and the fracture width have been determined as functions of time and place for three loss conditions: (1) no fluid loss, (2) fluid loss proportional to time, and (3) fluid loss proportional to the square root of time. proportional to the square root of time. From the results of the analysis, it is concluded that even under the unfavorable conditions of turbulent flow in the fracture and fluid loss, acid penetration is, in general, not a limiting factor in penetration is, in general, not a limiting factor in the application of the acid-fracturing process. However, it will not be possible to predict the productivity increase resulting from a given productivity increase resulting from a given treatment until more experimental data on the conductivity of etched fractures and on certain aspects of the reaction kinetics have been gathered. Introduction Acid-fracturing treatments are frequently applied to improve well productivity in limestone formations. In this process, hydrochloric acid is injected into a hydraulically induced fracture, which extends diametrically from the wellbore into the formation. During injection, the limestone faces of the fracture are dissolved. As a result, acid is consumed and its concentration decreases in the direction of flow. The width of the fracture increases, and the fracture faces may become irregularly etched as a result of the natural anisotropies of the formation. The etching pattern produced may contribute to an improvement in fracture conductivity after the fracture is allowed to close. The extent of this etching into the fracture and its final fluid conductivity determine the increase in productivity. Barron et al. have presented an empirical formulation of the acid-fracturing process for laminar flow conditions without fluid loss. When a theoretical description given by Prins et al. concerning the heat-transfer in laminar flow between parallel plates, is applied to the acid-fracturing parallel plates, is applied to the acid-fracturing process, the acid concentration in a fracture for process, the acid concentration in a fracture for steady-state laminar flow can be exactly described, provided that the fracture width is constant and no provided that the fracture width is constant and no fluid loss occurs. A comparison of the acid concentrations calculated from the empirical reaction-rate data of Barron with those theoretically derived according to Prins shows that these values are of the same order of magnitude and can be made equal for acceptable values of the diffusion rate only in the range of low velocities. Judging from the experimental set-up of Barron, we believe that for higher velocities the entrance transition length for fully developed laminar flow should be longer. For this reason, no agreement in the higher velocity ranges can be expected. This view is supported by Williams et al., who compared theoretically derived reaction rates in the heterogeneous calcium-carbonate /hydrochloric-acid system with those of Barron et al., who also conclude that entry effects may be responsible for the discrepancies in the higher velocity range. Nierode and Williams determined a kinetic model for the heterogeneous reaction of hydrochloric acid with limestone. The reaction order and rate constant used in their model were obtained from experiments. On the basis of this model, they derived an acid-fracturing design for laminar flow conditions including fluid loss. In the study described below, the acid-fracturing process has been reconsidered for turbulent-flow process has been reconsidered for turbulent-flow conditions in which both fluid loss and change in fracture width have been taken into account. We feel that the study provides a more realistic description of the process for both a vertical and horizontal fracture and that it may be used as a basis for designing acid-fracturing treatments.

ACIDIZATION III-THE KINETICS OF THE DISSOLUTION OF SODIUM AND POTASSIUM FELDSPAR IN HF / HCl ACID MIXTURES

Novel Approach for Sandstone Acidizing Using in Situ-Generated Hydrofluoric Acid with the Aid of Thermochemicals

An Overview of Current Acid Fracturing Technology With Recent Implications for Emulsified Acids

CO2 Sequestration in Feldspar-Rich Sandstone: Coupled Evolution of Fluid Chemistry, Mineral Reaction Rates, and Hydrogeochemical Properties

Boosting Reaction Rate of Acids for Better Acid Fracturing Stimulation of Dolomite-Rich Formations

Kinetics Study of Surface Reaction Between Acid and Sandstone Based on the Rotation Disk Instrument

Study on the Performance Degradation of Sandstone under Acidification

Kinetics of Estonian Phosphate Rock Dissolution in Hydrochloric Acid

The Dissolution Behavior of Feldspar Minerals in Various Low-Molecular-Weight Organic Acids

The use of a surface complexation model to describe the kinetics of ligand-promoted dissolution of anorthite

REACTIVE MECHANISM OF POTASSIUM FELDSPAR DISSOLUTION UNDER HYDROTHERMAL CONDITION

The complex effect of organic acids on the dissolution of feldspar at high temperature

Qualitative dissolution modeling of etch‐pit formation on the K‐feldspar surface through phase‐field approach

Minerals Dissolution Effect on the Mechanical Properties of Synthetic Carbonate Rocks

Reaction Kinetics and Coreflooding Study of High-Temperature Carbonate Reservoir Stimulation Using GLDA in Seawater

Study on reservoir damage during acidizing for high-temperature and ultra-deep tight sandstone

CO2-Rock-Brine Interactions in Feldspar-Rich Sandstones That Underwent Intense Heating

An Analysis of the Acidizing Process in Acid Fracturing

Minimizing Calcium Lactate Precipitation Via the Addition of Gluconate Ions for Matrix Acidizing with Lactic Acid

Effect of Cation Chloride Concentration on the Dissolution Rates of Basaltic Glass and Labradorite: Application to Subsurface Carbon Storage

Effects of sodium and potassium concentrations on dolomite formation rate, stoichiometry and crystallographic characteristics