Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Functionally graded polymers and ceramic adhesives: dynamic, viscoelastic, and thermal stability analysis

Thermal Degradation and Flammability of Nanocomposites Composed of Silica Cross-Linked to Poly(Methyl Methacrylate)

Thermal Stability of Optically Transparent Alpha-Zirconium Phosphate/Poly(methyl Methacrylate) Nanocomposites with High Particle Loading

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Thermal Stability and Dynamic Mechanical Behavior of Functional Multiphase Boride Ceramics/epoxy Composites

Thermal Degradation Kinetics and Viscoelastic Behavior of Poly(Methyl Methacrylate)/Organomodified Montmorillonite Nanocomposites Prepared via In Situ Bulk Radical Polymerization

Characterization of the mechanical properties and thermal conductivity of epoxy-silica functionally graded materials

Rheological, flame retardancy, and thermomechanical properties of polymethyl methacrylate composites: Effects of flame retardant and toughener

Finite Element Analysis of Thermal Residual Stress in Ceramic Functional Graded Material: Interface Optimization for Residual Reduction

Fabrication and mechanical behavior of structurally graded material (ceramic-reinforced polylactic acid/polylactic acid) for integrated engineering application

Thermogravimetric evaluation of PC/ABS/montmorillonite nanocomposite

Mechanical and viscoelastic characterization of Al 2 O 3 based polymer nanocomposites: An experimental and molecular dynamics simulation approach

Tribological performance of functional coated fiber reinforced additively manufactured polymer composite

Performance evaluation of structurally graded material fabricated through additive manufacturingLeistungsbewertung additiv gefertigter strukturell graduierter Werkstoffe

Understanding the influence of configurations and intermolecular interaction on thermomechanical and dynamics properties of polymer–clay nanocomposites via molecular dynamics simulations

Effect of graphene/silicon dioxide fillers addition on mechanical and thermal stability of epoxy glass fibre composite

Thermogravimetric Kinetic Analysis of PC/ABS/montmorillonite Nanocomposites

Effect of the alumina micro-particle sizes on the thermal conductivity and dynamic mechanical property of epoxy resin

Effects of graphene, alumina, and their hybrid on dynamic mechanical behavior of epoxy-based nanocomposites

Thermal stability modeling of high molecular weight polymethylmethacrylate TiO2 nanocrystals nanocomposites: Effect of loading and morphology

The effect of alumina nanoparticles on the thermal properties of PMMA: a molecular dynamics simulation