Abstract:The preservation states of excavated/salvaged waterlogged wooden artifacts vary greatly. The inhomogeneity of degradation and restricted acquirement of sampling make many necessary qualitative or quantitative analyses of wood properties and protection effect evaluation tests difficult to carry out. Therefore, it is urgent to develop a laboratory-controlled artificial degradation method to obtain sufficient waterlogged wood samples with good repeatability and uniform properties for preservation method research. This paper selected sound Pinus sp. wood to make artificially degraded waterlogged wood by NaOH-vacuum impregnation-hydrothermal combined method. The maximum water content (MWC) of the artificially degraded waterlogged wood was 260%, 340% and 575%, respectively, corresponding with the widely recognized degradation states level of low, medium and high degraded waterlogged archaeological wood according to their MWCs. Fourier transform infrared spectroscopy (FTIR) results indicated that the cellulose structure of the wood was well preserved though the hydrogen bond partially broke. Hemicellulose was degraded significantly, the main chain, as well as side chain, were broken, and the characteristic peak at 1 732 cm i disappeared; Lignin was partially degraded, and the relative intensity of the vibration absorption peak of aromatic lignin ring at 1 508 cm i decreased and shifted. Near-infrared reflectance spectroscopy (NIR) showed that all the three major components in the samples were degraded. Hemicellulose was the most degraded, followed by lignin. The increase of relative content of lignin, reflected by the increase of relative content of C=0. A broad peak was formed in the 1 536-1 580 nm region with decreased peak intensity, indicating that the hydrogen bond structure within and between molecules in the cellulose crystallization region was broken. Compared with traditional methods, the concentration of NaOH solution using the combined method was reduced from more than 50% to and the treatment time was significantly shortened from several months to 10 hours, which proved that the degradation efficiency was greatly improved. The MWC and the degradation degree of the chemical structure of wood cell wall of artificially degraded waterlogged wood was many controller and higher than that of the existing methods. The state and performance of artificial waterlogged wood in this research were similar to archaeological wood.

Rubberwood (Hevea brasiliensis) preservation using sodium acetate and sodium butyrate from fermented landfill leachate

Determination of changes in the mechanical and color properties of some wood species treated with shellac

Production and Potential Application of Pyroligneous Acids from Rubberwood and Oil Palm Trunk as Wood Preservatives through Vacuum-Pressure Impregnation Treatment

Wood biowaste in goatskin preservation to reduce salinity in the tannery wastewater

Mechanical properties and biological durability in soil contact of chemically modified wood treated in an open or in a closed system using glycerol/maleic anhydride systems

Comparative studies on the durability and moisture performance of wood modified with cyclic N-methylol and N-methyl compounds

Wood modification with N-methylol and N-methyl compounds: a case study on how non-fixated chemicals in modified wood may affect the classification of their durability

Eco-friendly and Mildly Modification of Wood Cell Walls with Heat Treated Wood Extracts to Improve Wood Decay Resistance

Preparation and Spectra Study of Artificially Degraded Waterlogged Wood

Employing a mixture of fine-particle PKS, glycerol, and citric acid as an eco-friendly binder for plywood production from rubberwood (Hevea brasiliensis) veneer

Suppression of Ganoderma boninense Using Benzoic Acid: Impact on Cellular Ultrastructure and Anatomical Changes in Oil Palm Wood

Improvement of Wood Decay Resistance by Salicylic Acid / Silica Microcapsule: Effects on the Salicylic Leaching, Microscopic Structure and Decay Resistance

Durability of Superheated Steam-Treated Light Red Meranti (Shorea spp.) and Kedondong (Canarium spp.) Wood against White Rot Fungus and Subterranean Termite

Enhancement of mechanical and flame-retardant properties of Acacia hybrid through the treatment of a combination of styrene-acrylic copolymer and sodium silicate

Study on preparation and properties of chloroprene rubber adhesive for wood working

Biocontrol potential of Bacillus subtilis B1 against sapstain fungus in rubber wood

Chemical, Biological and Mechanical Characterization of Wood Treated with Propolis Extract and Silicon Compounds

Preparation and properties of a novel wood adhesive derived from antibiotic bacterial residues

Improvement of the Dimensional Stability of Rubber Wood Based on the Synergies of Sucrose and Tung Oil Impregnation

Study on Bonding Capacity of the Rubber Wood

Hydraulic conductivity of some perishable wood species in Southeastern Nigeria: A quantitative approach to determine their treatability