Abstract:Titanium boride (TiB2) is a material classified as an ultra-high-temperature ceramic. The TiB2 structure is dominated by covalent bonds, which gives the materials based on TiB2 very good mechanical and thermal properties, making them difficult to sinter at the same time. Obtaining dense TiB2 polycrystals requires a chemical or physical sintering activation. Carbon and molybdenum disilicide (MoSi2) were chosen as sintering activation additives. Three series of samples were made, the first one with carbon additives: 0 to 4 wt.%; the second used 2.5, 5 and 10 wt.% MoSi2; and the third with both additions of 2 wt.% carbon and 2.5, 5 and 10 wt.% MoSi2. On the basis of the dilatometric sintering analysis, all additives were found to have a favourable effect on the sinterability of TiB2, and it was determined that sintering TiB2 with the addition of carbon can be carried at 2100 °C and with MoSi2 and both additives at 1800 °C. The polycrystals were sintered using the hot-pressing technique. On the basis of the studies conducted in this work, it was found that the addition of 1 wt.% of carbon allows single-phase TiB2 polycrystals of high density (>90%) to be obtained. The minimum MoSi2 addition, required to obtain dense sinters with a cermet-like microstructure, was 5 wt.%. High density was also achieved by the materials containing both additives. The samples with higher MoSi2 content, i.e., 5 and 10%, showed densities close to 100%. The mechanical properties, such as Young's modulus, hardness and fracture toughness (KIc), of the polycrystals and composites were similar for samples with densities exceeding 95%. The Vickers hardness was 23 to 27 GPa, fracture toughness (KIC) was 4 to 6 MPa·m0.5 and the Young's modulus was 480 to 540 GPa. The resulting TiB2-based materials showed potential in high-temperature applications.

Impact of TiB2 source on the microstructure and properties of TiB2–SiC–B4C ceramics

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Effect of TiB2 particles on microstructure and mechanical properties of B4C–TiB2 ceramics prepared by hot pressing

Effects of Boron Content on the Microstructure and Properties of BxC-TiB2 (x=4.5, 6.5 or 8.5) Ceramic Composites by the Reactive Spark Plasma Sintering

Processing, Microstructure and Mechanical Properties of TiB2-MoSi2-C Ceramics

Comparison of the effects of MoSi2 and CrSi2 on sintering and properties of titanium diboride (TiB2)

Influence of TiB2 and CrB2 on densification, microstructure, and mechanical properties of ZrB2 ceramics

Effects of TiB2 Particles on the Microstructure Evolution and Mechanical Properties of B4C/TiB2 Ceramic Composite

Microstructure and properties of hot pressed TiB2 and SiC reinforced B4C–based composites

TiB2 effects on the AlMgB14–TiB2 ceramics structure and properties

Effects of boron source on properties of pressureless solid-state sintered silicon carbide ceramics

Fabrication and characterization of SiC–TiB 2 composite ceramics used as infrared source material

Influence of titanium diboride on the microstructure and mechanical properties of silicon nitride ceramic

Enhanced Mechanical/electrical Properties of in Situ Synthesized SiC-TiB2 Ceramic Composites by Reactive Hot-Pressing Sintering

Effect of Powder Synthesis Processing on Microstructure and Mechanical Properties of TiB2-TiC Composite Ceramics

Ceramic Matrix Composites Obtained by the Reactive Sintering of Boron Carbide with Intermetallic Compounds from the Ti-Si System

Effect of Titanium Carbide Addition on the Thermoelectric Properties of B4C Ceramics

Effect of Ti Doping on the Mechanical Properties of B4C Composite Ceramics

Microstructure and mechanical properties of b4c-tib2 composites reactive sintered from B4C + TiO2 precursors

Microstructural characterization of TiB2–SiC–BN ceramics prepared by hot pressing