Abstract:Ti2AlNb alloy is a new type of lightweight and heat-resistant structural material that has been an active research topic with multi-phases due to its improved mechanical properties. However, the phase response under severe plastic deformation (SPD) at high strain rates is unclear, which limits the understanding of its strengthening mechanism. Here, laser shock peening (LSP) was employed to investigate the microstructure response of alpha 2, O, and B2/beta phases in Ti2AlNb alloy. After LSP, the highest density dislocations were generated in the B2/beta phases, followed by the O phases, and the least dislocations were observed in the alpha 2 phases. In the B2/beta phases, only dislocation tangles (DTs) were observed. Dislocation lines (DLs) and DTs were mainly distributed in the O phases. As for the alpha 2 phases, DLs were generated while a small number of DTs were piled up at the grain boundaries. In addition, parallel dislocations (PDs) with a spacing of about 135 nm can be observed on the surface of the alpha 2 phases, and the dislocations interspersed between PDs were composed of screw dislocations with long segments. In addition to dislocation structures, stacking faults (SFs) were observed in both alpha 2 phases and O phases, and mechanical twins were formed in the O phases, which were generated to coordinate the SPD induced on the surface. These dislocation structures formed dislocation cells (DCs) and sub-grain boundaries which further developed into high-angle grain boundaries (HAGBs) together with mechanical twins, dividing the coarse grains and refining the microstructure. As the depth increased, the responses of the three kinds of phases decreased. The PDs in the alpha 2 phases have widened spacing and could not penetrate the grains. The mechanical twins were gradually reduced until no obvious twin structure could be observed. Finally, dislocations, grain size, microhardness, and residual stress presented a gradient distribution. The improved microhardness (maximum 470 HV) and compressive residual stress (maximum -600 MPa) which were consistent with the refined grains and highdensity dislocations gradually decreased to that of the base metal (BM).

Experimental study on the collapse behavior of graded Ti-6Al-4V micro-lattice structures printed by selective laser melting under high speed impact

Investigation of Compressive Properties of Graded Lattice Structure with Different Porosity Gradient Spans Prepared by Selective Laser Melting

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Mechanical Properties Evaluation Based on the Variable Gradient of Body-Centered-Cubic-Based Lattice Structure Prepared by Laser Powder Bed Fusion

Quasi-Static compressive responses and fatigue behaviour of Ti-6Al-4 V graded lattice structures fabricated by laser powder bed fusion

Compressive properties of imperfect Ti-6Al-4V lattice structure fabricated by electron beam powder bed fusion under static and dynamic loadings

Microstructural features and compressive properties of SLM Ti6Al4V lattice structures

Effect of heat treatment on mechanical properties, failure modes and energy absorption characteristics of lattice skeleton and sheet structures fabricated by SLM

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Mechanical behavior and failure mode of body-centered cubic, gyroid, diamond, and Voronoi functionally graded additively manufactured biomedical lattice structures

A detailed analysis on the microstructure and compressive properties of selective laser melted Ti6Al4V lattice structures

Mechanical Response of Gradient Lattice Structures Based on Topology Optimization

Evaluation of mechanical properties of Ti–6Al–4V BCC lattice structure with different density gradient variations prepared by L-PBF

Experimental Evaluation of the Effects of Discrete-Grading-Induced Discontinuities on the Material Properties of Functionally Graded Ti-6Al-4V Lattices

Dynamic compressive properties and underlying failure mechanisms of selective laser melted Ti-6Al-4V alloy under high temperature and strain rate conditions

Influence of Density Gradient on the Compression of Functionally Graded BCC Lattice Structure

Mechanical behaviour of additively manufactured Ti6Al4V meta-crystals containing multi-scale hierarchical lattice structures

Dynamic mechanical behavior of additively manufactured bio-inspired metallic lattice structure subjected to high strain rate impact loading

Gradient microstructure response in different phases of Ti<sub>2</sub>AlNb alloy with laser shock peening

Physical-Mechanical Characteristics and Microstructure of Ti6Al7Nb Lattice Structures Manufactured by Selective Laser Melting

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting