Abstract:The development of process steps catalyzed by immobilized enzymes usually encompasses the screening of enzyme variants, as well as the optimization of immobilization protocols and process parameters. Direct immobilization of biocatalysts by physical entrapment into hydrogels can be applied to reduce the effort required for immobilization, as the enzyme-specific optimization of the immobilization procedure is omitted. Physical entrapment is applicable for purified enzymes as well as crude cell extracts. Therefore, it can be used to quickly assess and compare activities of immobilized enzymes. For the application in flow reactors, we developed 3D-printed hydrogel lattices for enzyme entrapment as well as matching housings, also manufactured by 3D-printing. Testing the resulting enzyme reactors for three different enzymes, namely alcohol dehydrogenase from Lactobacillus brevis, benzoylformate decarboxylase from Pseudomonas putida and β-galactosidase from Aspergillus oryzae, and four different enzymatic reactions showed the broad applicability of the approach but also its limitations. The activity of the immobilized biocatalysts was measured in batch experiments and compared to the kinetics of the respective free enzymes in solution. This comparison yields an effectiveness factor, which is a key figure to describe the extent the immobilized catalyst is effectively utilized. For the examined systems the effectiveness factor ranged between 6 and 14% and decreased with increasing absolute activity of the entrapped enzymes due to mass transfer limitations. To test the suitability of the hydrogel lattices for continuous operation, they were inserted into 3D-printed reactor housings and operated at constant flow. Stable product formation could be monitored over a period of 72 h for all four enzymatic systems, including two reactions with redox cofactor regeneration. Comparing calculated and experimental conversion in the continuous setup, higher values of the effectiveness factor in batch experiments also hint at good performance in continuous flow. This can be used to optimize complex biocatalytic reactions on a small scale.

Design of 3D‐Printed Heterogeneous Reactor Systems To Overcome Incompatibility Hurdles when Combining Metal and Enzyme Catalysis in a One‐Pot Process

Direct ink writing of Pd-Decorated Al<sub>2</sub>O<sub>3</sub> ceramic based catalytic reduction continuous flow reactor

3D‐Printed Structured Reactor with Integrated Single‐Atom Catalyst Film for Hydrogenation

3D printed ceramics as solid supports for enzyme immobilization: an automated DoE approach for applications in continuous flow

Precise 2D-Patterned Incompatible Catalysts for Reactions in One-Pot.

Bio-inspired Creation of Heterogeneous Reaction Vessels Via Polymerization of Supramolecular Ion Pair

Multistep One-Pot Reactions Combining Biocatalysts and Chemical Catalysts for Asymmetric Synthesis

Merging High-Pressure Syngas Metal Catalysis and Biocatalysis in Tandem One-Pot Processes for the Synthesis of Nonchiral and Chiral Alcohols from Alkenes in Water

The 3D-Printing Fabrication of Multichannel Silicone Microreactors for Catalytic Applications

3D Printing and Chemical Dealloying of a Hierarchically Micro- and Nanoporous Catalyst for Wastewater Purification

Coupling metal and whole-cell catalysis to synthesize chiral alcohols

Tailored monolithic catalyst and reactor by direct photo-curing 3D printing for oxidative desulfurization of fuels

3D-printed metal-organic framework encapsulated Keggin heteropolyacid for catalytic purpose

Fabricating a Structured Single‐Atom Catalyst via High‐Resolution Photopolymerization 3D Printing

Bottom-Up Synthesis of Multicompartmentalized Microreactors for Continuous Flow Catalysis

Continuous Flow Biocatalytic Reductive Amination by Co-Entrapping Dehydrogenases with Agarose Gel in a 3D-Printed Mould Reactor

Bridging the incompatibility gap in dual asymmetric catalysis over a thermoresponsive hydrogel-supported catalyst

Optimized Spatial Configuration of Heterogeneous Biocatalysts Maximizes Cell-Free Biosynthesis of ω-Hydroxy and ω-Amino Acids

Enzyme-metal-single-atom Hybrid Catalysts for One-Pot Chemoenzymatic Reactions

Unspecific peroxygenase immobilization in 3D-printed microfluidics: Towards tailor-made screening platforms

Advantages of Hydrogel-Based 3D-Printed Enzyme Reactors and Their Limitations for Biocatalysis