Abstract:In this paper, Polyethylene Terephthalate Glycol (PETG) has been used as a novel thermoplastic thermo-responsive Shape Memory Polymer (SMP) with biocompatibility, excellent printability, cost efficiency, and transparency for the 3D/4D printing of porous structures by material extrusion. The high deformability of PETG allows for programming without an increase in temperature or the need for additional operations. This enabled the use of PETG for the Cold Programming (CP) of ordered porous shape memory structures, made possible by material extrusion printing technology. The porous samples were printed employing three patterns and two porosity percentages. The programming operation was performed at ambient temperature by applying different amounts of pre-strains under constrained and unconstrained compression modes. The constrained test was conducted using a mandrel and a matrix for exerting pure volume reduction (pure packing). The shape recovery test was accomplished above the glass transition temperature (T g ), and the fixity and recovery ratios were recorded. Employing 3D printing provided the ability to manufacture porous thermoplastic SMP structures with highly controllable pores geometry and sizes for different porosity percentages. The results showed that the combination of the uniform strain distribution in the porous structures with the help of the 3D printing process and CP on the new PETG SMP makes it possible to achieve high deformation in the glassy region, resulting in a complete shape recovery for two lozenge and vertical patterns. Among all specimens, constrained specimens by horizontal pattern had the highest fixity ratio of 90.7%. However, low fixity ratios in CP can be justified considering the existence of two stages of spring-back and structural relaxation after unloading, resulting from the elastic and viscoelastic behavior. Increasing Infill Density (ID) along with the constrained test (pure packing) improved the shape fixity. The existence of higher mechanical constraints and harsher localized deformation are speculated to be the case for this observation. Applying higher deformations (40 to 80%), for both designed tests, brought about a weakness in the shape memory performance, while it improved for 100% volume reduction.

Assessment of mechanical properties and shape memory behavior of 4D printed continuous fiber-reinforced PETG composites

4D printing and annealing of PETG composites reinforced with short carbon fibers

Poly(ethylene terephthalate) Glycol/Carbon Black Composites For 4D Printing

4D-printed PLA-PETG polymer blends: comprehensive analysis of thermal, mechanical, and shape memory performances

Continuous Fiber-Reinforced Aramid/PETG 3D-Printed Composites with High Fiber Loading through Fused Filament Fabrication

Additively Manufactured Carbon Fibre PETG Composites: Effect of Print Parameters on Mechanical Properties

4D Printing of Continuous Fiber-Reinforced Electroactive Smart Composites by Coaxial Additive Manufacturing

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Design, processing, 3D/4D printing, and characterization of the novel PETG–PBAT blends

Optimization of Flexural Performance of PETG Samples Produced by Fused Filament Fabrication with Response Surface Method

Enhancing shape memory properties of multi-layered and multi-material polymer composites in 4D printing

A Continuous Fiber-Reinforced Additive Manufacturing Processing Based on PET Fiber and PLA

Development of Fiber-Reinforced Polymer Composites for Additive Manufacturing and Multi-Material Structures in Sustainable Applications

The Impact Of Carbon Fiber on the surface properties of the 3D Printed PEGT Product

Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures

Cold programming of ordered porous PETG 4D printed by material extrusion

Mechanical performances of printed carbon fiber-reinforced PLA and PETG composites

Investigating the influence of annealing and nozzle diameter on tensile strength of polyethylene terephthalate glycol composites

Effects of printing parameters on the mechanical characteristics and mathematical modeling of FDM-printed PETG

4D printing of heat‐stimulated shape memory polymer composite for high‐temperature smart structures/actuators applications

4D printing of shape memory polyethylene terephthalate glycol/thermoplastic polyurethane (PETG/TPU) blends